Instruction Set Architecture
ISA is the abbreviation for Instruction Set Architecture. MIPS processors have been in production since 1988. Over time several enhancements of the architecture were made. The different revisions which have been introduced are MIPS I, MIPS II, MIPS III, MIPS IV and MIPS V. Each revision is a superset of its predecessors. When MIPS was spun out of SGI again in 1998, they refocused on the embedded market. At that time, this superset property was found to be a problem, and the architecture definition was changed to define a 32-bit MIPS32 and a 64-bit MIPS64 architecture. Frequently the terms MIPS32 and MIPS64 are meant to indicate some generic 32-bit and 64-bit MIPS processor, respectively.
MIPS II was introduced by the R6000. It adds load linked, store conditional and branch likely instructions. The FPU's instruction set was improved by support of 64-bit loads and stores which halved the number of instructions needed to load or store a double precision floating point register when compared to MIPS I.
MIPS III was introduced 1992 in the R4000. It adds 64-bit registers and integer instructions and a square root FP instruction.
MIPS IV adds conditional moves and an inverse square root FPU instruction. The R8000 was the first to implement the MIPS IV instruction set.
MIPS V was specified in 1994 by SGI but never actually implemented by any processor. MIPS64 is a superset of MIPS V
MIPS32 is the 32-bit subset of MIPS64. The current version is MIPS32 Release 5. Most MIPS32 cores shipping today implement Release 2 of the architecture.
MIPS64 is a superset of the MIPS V. The current version is MIPS64 Release 5. Most current production MIPS64 cores implement Release 1 of the MIPS64 architecture but a few also implement Release 2.
MIPS32/64 Release 2
Release 2 improves SMP support including the PAUSE instruction and more memory barriers (SYNC).
MIPS32/64 Release 3
On the privileged architecture side it added read inhibit (RI) and execute inhibit (XI) bits to the TLB. It also added EVA to extend the usable virtual address space, and hardware page walking.
MIPS32/64 Release 5
Application Specific Extensions (ASE)
The DSP ASE is an optional extension to the MIPS32/MIPS64 release 2 instruction sets which can be used to accelerate a large range of "media" computations - particularly audio, since TV-resolution video is way beyond the power of general-purpose CPUs for the next few years. The DSP ASE assumes that you're running on a Release 2 chip since there are things that are in Release 2 that are critical to the performance of media applications written using the DSP ASE.
Unlike the bulk of the MIPS architecture, it's a fairly irregular set of operations, many chosen for its particular relevance to some key algorithm.
Its main novel features (vs original MIPS32):
- Saturating arithmetic (when a calculation overflows, deliver the representable number closest to the non-overflowed answer).
- Fixed-point arithmetic on signed 32- and 16-bit fixed-point fractions with a range of -1 to +1 (these are widely called "Q31" and "Q15").
- The existing MIPS32 instruction set includes integer multiplication and multiply-accumulate which delivers results into a double-size accumulator (called "hi/lo" and 64 bits on MIPS32 CPUs). The DSP ASE adds three more accumulators, and some different flavours of multiply-accumulate.
- SIMD instructions operating on 4 x unsigned bytes or 2 x 16-bit values packed into a 32-bit register (the 64-bit variant of the DSP ASE supports larger vectors, too).
- SIMD operations are basic arithmetic, shifts and some multiply-accumulate type operations.
To write DSP-ASE-enabled programs, you'll need to write assembler code or use the "intrinsics" (built-in pseudo-subroutines) which are more or less 1-to-1 with the underlying instructions.
Linux 2.6.12-rc5 starting 2005-05-31 adds support for the DSP ASE. Note that to actually make use of the DSP ASE a toolchain which support this is required. As of this writing only MIPS SDE has such support.
The MIPS instruction set is by far too complex to be covered on this page. The freely available CPU specs are not an easy reading for a first time MIPS'er either. So here are some literature recommendations in no particular order: