First get Linux/MIPS kernel sources, for example from CVS. In the next step we need to configure the kernel sources by running make config, make menuconfig, make xconfig
The recommended compiler for building Linux 2.4 is gcc 2.95 however the large majority of developers is probably user a more modern GCC. New compilers up to gcc 3.3 have been used successfully to build the kernel and only the latest 2.4 kernels have fixed the issues with gcc 3.4. GCC 4.x can not be used and with Linux 2.4 being in deep freeze mode we generally don't intend to fix such problems but rather recommend to use an older compiler for the kernel.
The latest official GCC 2 is version 2.95.3. GCC 2.96 is an unofficial, massively patched version. It provides more efficient optimization with -O2, more strict syntax checking and supports more recent C++ standards. Unfortunately the C++ ABI is not fully compatible with the official 2.95.3 nor 3.0. This is not a concern for building the kernel or modules as those are written in plain C but is a consideration if using a single toolchain for an entire distribution or product.
The following is about building vanilla linux-mips.org kernels using unmodified GNU toolchains. Further requirements are documented in Documentation/Changes. Below are additional MIPS-specific requirements. If you're trying to build a vendor kernel, please consider using the vendor supplied or recommended toolchain.
- The Lemote 2F defconfig build requires binutils 2.20.2 or binutils 2.21 which at the time of this writing are both still unreleased. It is not clear when they will be released. Alternatively a CVS version can be used; for details see the binutils web pages.
- GCC 3.2 is a lost cause for building 64-bit kernels
- GCC 3.3 is broken for 64-bit kernels but can just about be kludged to build a 64-bit kernel.
- GCC 4.4 or a patched older version is required to build a kernel O2 or Indigo² with R10000 processors.
- GCC 3.2 used to work for the rest but it's a very long time since I tested this for a modern kernel.
- Linux 2.6.29 and older need a GCC older than 4.4.0 to compile. This dependency is being fixed on 2010-05-29 while writing this so you may have to update your kernel to get rid of this dependency.
- Linux 2.6.16 and older need a GCC older than 4.3.0 to compile.
Problems caused by non-Linux/MIPS toolchain
make: Entering directory `/usr/src/linux-mips/arch/mips/kernel' mips_4KC-gcc -D__ASSEMBLY__ -D__KERNEL__ -I/usr/eldk/usr/src/linux-mips/include -D_MIPS_SZLONG=32 -D_MIPS_SZPTR=32 -D_MIPS_SZINT=32 -g -G 0 -mno-abicalls -fno-pic -pipe -c -o entry.o entry.S entry.S: Assembler messages: entry.S:225: Error: unrecognized opcode `reg_s $8,164($29)' entry.S:226: Error: unrecognized opcode `reg_s $8,164($29)'
_MIPS_SZLONG etc. are normally defined by the gcc compiler driver. That is they should never be defined by the application itself. The precense of such kludgery usually indicates the use of a toolchain that wasn't configured for a Linux/MIPS target.
ld dies with signal 6
collect2: ld terminated with signal 6 [Aborted]
This is a known bug in some very old binutils versions. You will have to upgrade to at least binutils 2.8.1 plus very current patches. With Linux 2.4 or newer binutils 220.127.116.11 or newer is probably recommended.
Linux 2.6 build fails early
$ make CHK include/linux/version.h HOSTCC scripts/basic/fixdep HOSTCC scripts/basic/split-include HOSTCC scripts/basic/docproc CC scripts/mod/empty.o gcc: cannot specify -o with -c or -S and multiple compilations make: *** [scripts/mod/empty.o] Error 1 make: *** [scripts/mod] Error 2 make: *** [scripts] Error 2
There are two possible causes for this failure known:
- Make sure you have set CONFIG_CROSSCOMPILE or add
CROSS_COMPILE=<target>to the make invocation.
- A few early Linux 2.6 kernels had a bug which would always result in this error message. In this case you really should upgrade.
This is caused by a linker bug that exists in at least binutils 2.15. If you hit it you should upgrade to binutils 2.16.