ADSL2MUE - Revision history

Mstombs: /* Console and JTAG port */

2010-11-05T21:32:18Z

‎Console and JTAG port

2009-06-26T15:06:53Z

‎Hidden software features

2009-06-03T07:33:05Z

‎Command Line Interface (CLI)

2009-06-03T07:32:33Z

‎Command Line Interface (CLI)

2009-01-07T00:22:41Z

‎External Links

2007-06-17T20:38:52Z

‎Console and JTAG port

2007-06-15T22:02:09Z

‎Console and JTAG port

2007-06-15T21:54:53Z

‎Hidden software features

2007-06-15T21:51:27Z

‎External Links

2007-06-15T21:47:57Z

@@ Line 133: / Line 133: @@
   |                      JP1 JTAG           |
   |             Vcc +3.3V Pin 14,13         |
-  |                 GND   Pin 12,11         |
+  |                 N/C   Pin 12,11         |
   |                 GND   Pin 10,9  TCK     |        Front of ADSL2MUE
   |                 GND   Pin 8,7   TMS     |

@@ Line 215: / Line 215: @@
 Oficial firmware includes a comand line interface that allows for a few more modes of operation. The standard web based GUI allows you to configure RFC2684 bridged mode with LLC or VC encapsulation only, but the CLI allows you to configure RFC2684 routed mode also.
-I got into the CLI through the console and after enabling privileges (CLI enable password matches web password) you can configure the WAN interface as statically managed and set RFC2684 routed as the interface type.
+I got into the CLI through the console and after enabling privileges (CLI enable password matches web password - or may be `Admin` with a case sensitive capital A) you can configure the WAN interface as statically managed and set RFC2684 routed as the interface type.
 Keep in mind that this hidden feature allows you to use this piece of hardware as a router connected to a routed mode RFC2684 ATM/DSL connection. Still work needs to be done on OpenWrt AR7 port to let this hardware become the modem it claims to be.  An experimental Half-Bridge mode script is now available using the extended Linux environment provide in the Routertech 2.3 3rd party firmware.

← Older revision		Revision as of 07:33, 3 June 2009
Line 222:		Line 222:

	*** Note: Firmware released as of before 1/6/2009 contains a massive update that allows many more features through the web front end including port forwarding UPnP and Firewalling (full router capabilities). Logging in by ssh is not so needed now. [[User:Jago25 98\|Jago25 98]] 07:32, 3 June 2009 (UTC)jago25_98		*** Note: Firmware released as of before 1/6/2009 contains a massive update that allows many more features through the web front end including port forwarding UPnP and Firewalling (full router capabilities). Logging in by ssh is not so needed now. [[User:Jago25 98\|Jago25 98]] 07:32, 3 June 2009 (UTC)jago25_98
		+

	You can make this modem act as a router (port forwarding) by using the command line interface.		You can make this modem act as a router (port forwarding) by using the command line interface.

← Older revision		Revision as of 07:32, 3 June 2009
Line 220:		Line 220:

	== Command Line Interface (CLI) ==		== Command Line Interface (CLI) ==
		+
		+	*** Note: Firmware released as of before 1/6/2009 contains a massive update that allows many more features through the web front end including port forwarding UPnP and Firewalling (full router capabilities). Logging in by ssh is not so needed now. [[User:Jago25 98\|Jago25 98]] 07:32, 3 June 2009 (UTC)jago25_98

	You can make this modem act as a router (port forwarding) by using the command line interface.		You can make this modem act as a router (port forwarding) by using the command line interface.

@@ Line 643: / Line 643: @@
 * [http://www.linksys.com/international/product.asp?coid=8&ipid=717 Linksys ADSL2MUE UK home page]
 * [http://openwrt.org/AR7Port OpenWRT version for AR7 Architecture]
-* [http://www.routertech.org Routertech 3rd party firmware for AR7 platform]
+* [http://www.routertech.org RouterTech 3rd party firmware for AR7 platform]
 [[Category: DSL routers]]

@@ Line 149: / Line 149: @@
 The console is located on the same edge that the leds are, that is, front-right side of the board. It is labeled J1 and an arrow points to pin 1 on the left, that is, the closest pin to the leds. Voltage reference is 3.3 volts and it is set by default at 38400,8,N,1 (but will revert to 9600,8,N,1 if config mtd3 deleted). Mine already had a connector soldered just like to ones we usually see on computer boards as CPU/NB fan connector.
-Pins 1 to 12 of the JTAG port are the same as the WRT54G/GS/GL, but for the HairyDairyMaid passive connector to function the link between VCC (Pin 14) and TRST (Pin 1) is required (with a 100 ohm resistor link in cable).
+Pins 1 to 12 of the [[JTAG]] port are the same as the WRT54G/GS/GL, but for the HairyDairyMaid passive connector to function the link between VCC (Pin 14) and TRST (Pin 1) is required (with a 100 ohm resistor link in cable).
 == Software resources ==

@@ Line 139: / Line 139: @@
   |                 GND   Pin 4,3   TDI     |
   |                 GND   Pin 2,1   TRST    |
-  |                                         led
+  |                                         |
-  |                                         led
+ |                 Internet                led  Green = GPIO 13, Red = GPIO 9
-  |                                         led
+  |                 DSL                     led  Green = GPIO 33
-  |                                         led
+  |                 USB                     led  GPIO 12
-  |                                         led
+  |                 Ethernet                led  Green = GPIO 15
   |_________________________________________|

@@ Line 2: / Line 2: @@
 '''If you are looking for a modem this might not be what you are looking for. Although advertised as a modem, it is actually a router with some sort of bridging capabilities.'''
 == Hardware resources ==
 Based on Texas Instruments [[AR7]] architecture it includes a few other chips on board, such as ethernet and ADSL transformers. TI does not provide with much information about the architecture and answers with a "this is for OEM eyes only" when asked for more information.
-This device provides ADSL, ethernet and USB conectivity only.
+This device provides ADSL, Ethernet and USB conectivity only.
-* Ethernet: One on-chip fast ethernet 10/100 port attached to a transformer from Delta Electronics labeled [http://www.delta.com.tw/product/cp/telecom/telecom_product3.asp?pcid=2&psid=1&ptid=2&ssid=1 LF8505 DELTA 0448W].
+* Ethernet: One on-chip fast Ethernet 10/100 port attached to a transformer from Delta Electronics labeled [http://www.delta.com.tw/product/cp/telecom/telecom_product3.asp?pcid=2&psid=1&ptid=2&ssid=1 LF8505 DELTA 0448W].
 * USB: One USB 1.1 port.
 * ADSL: One on-chip adsl port attached to an ADSL2 transformer from Linkcomm Manufacturing labeled [http://www.linkcom-co.com/english/products/prd_list.asp?cateid=97 LAL0671 LINKCOM 0450]. Advertised explicitly as AR7 compatible.