linux-mips
[Top] [All Lists]

[PATCH V2 1/2] DT: Add documentation for gpio-falcon

To: Grant Likely <grant.likely@linaro.org>
Subject: [PATCH V2 1/2] DT: Add documentation for gpio-falcon
From: John Crispin <blogic@openwrt.org>
Date: Fri, 9 Aug 2013 21:10:18 +0200
Cc: Rob Herring <rob.herring@calxeda.com>, John Crispin <blogic@openwrt.org>, linux-mips@linux-mips.org, devicetree@vger.kernel.org, linux-gpio@vger.kernel.org
List-archive: <http://www.linux-mips.org/archives/linux-mips/>
List-help: <mailto:ecartis@linux-mips.org?Subject=help>
List-id: linux-mips <linux-mips.eddie.linux-mips.org>
List-owner: <mailto:ralf@linux-mips.org>
List-post: <mailto:linux-mips@linux-mips.org>
List-software: Ecartis version 1.0.0
List-subscribe: <mailto:ecartis@linux-mips.org?subject=subscribe%20linux-mips>
List-unsubscribe: <mailto:ecartis@linux-mips.org?subject=unsubscribe%20linux-mips>
Original-recipient: rfc822;linux-mips@linux-mips.org
Sender: linux-mips-bounce@linux-mips.org
Describe the GPIO banks found on the MIPS based Lantiq Falcon SoC.

Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
---
Changes in V2:
* fixed a typo
* add a more explicit description

 .../devicetree/bindings/gpio/gpio-falcon.txt       |   27 ++++++++++++++++++++
 1 file changed, 27 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/gpio/gpio-falcon.txt

diff --git a/Documentation/devicetree/bindings/gpio/gpio-falcon.txt 
b/Documentation/devicetree/bindings/gpio/gpio-falcon.txt
new file mode 100644
index 0000000..40558b5
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-falcon.txt
@@ -0,0 +1,27 @@
+Lantiq Falon SoC GPIO controller bindings
+
+This MIPS based GPON SoC has 5 banks of up to 32 gpios.
+
+Required properties:
+- compatible:
+  - "lantiq,falcon-gpio" for Falcon SoC controllers
+- #gpio-cells : Should be two.
+  - first cell is the pin number
+  - second cell is used to specify optional parameters (unused)
+- gpio-controller : Marks the device node as a GPIO controller
+- reg : Physical base address and length of the controller's registers
+- interrupt-parent: phandle to the IM device node that the irq is routed via
+- interrupts : Specify the IM interrupt number
+- lantiq,bank : The physical GPIO bank that this block is associated with
+
+Example:
+
+       gpio0: gpio@810000 {
+               compatible = "lantiq,falcon-gpio";
+               #gpio-cells = <2>;
+               gpio-controller;
+               reg = <0x810000 0x80>;
+               interrupt-parent = <&icu0>;
+               interrupts = <44>;
+               lantiq,bank = <0>;
+       };
-- 
1.7.10.4


<Prev in Thread] Current Thread [Next in Thread>
  • [PATCH V2 1/2] DT: Add documentation for gpio-falcon, John Crispin <=