linux-mips
[Top] [All Lists]

Re: development board?

To: "Oliver Kowalke" <oliver.kowalke@gmx.de>, milang@tal.org, ralf@linux-mips.org
Subject: Re: development board?
From: "Oliver Kowalke" <oliver.kowalke@gmx.de>
Date: Fri, 03 Aug 2012 17:46:26 +0200
Cc: linux-mips@linux-mips.org
In-reply-to: <20120803154011.214590@gmx.net>
List-archive: <http://www.linux-mips.org/archives/linux-mips/>
List-help: <mailto:ecartis@linux-mips.org?Subject=help>
List-id: linux-mips <linux-mips.eddie.linux-mips.org>
List-owner: <mailto:ralf@linux-mips.org>
List-post: <mailto:linux-mips@linux-mips.org>
List-software: Ecartis version 1.0.0
List-subscribe: <mailto:ecartis@linux-mips.org?subject=subscribe%20linux-mips>
List-unsubscribe: <mailto:ecartis@linux-mips.org?subject=unsubscribe%20linux-mips>
References: <50085CB4.3030205@gmx.de> <1343917513.13395.6.camel@ubctp.tal.org> <20120803062242.GA22167@linux-mips.org> <20120803154011.214590@gmx.net>
Sender: linux-mips-bounce@linux-mips.org
Atheros AR7161 == 32-bit MIPS 24K processor core

price ca 85,- euros

> I'll try MikroTik RouterBOARD 450G:
> 
>     CPU: AR7161 680MHz
>     Memory 256MB DDR SDRAM onboard memory
>     Boot loader RouterBOOT
>     Data storage 512MB onboard NAND memory chip, microSD slot on back side
>     Ethernet Five 10/100/1000 Mbit/s Ethernet ports with Auto-MDI/X
>     miniPCI none
>     Extras Reset switch, Beeper
>     Serial port One DB9 RS232C asynchronous serial port
>     Power, NAND activity, 5 user LEDs
>     Power options Power over Ethernet: 18-28V DC (except power over
> datalines). Power jack: 8-28V DC
>     Dimensions 9 cm x 11.5 cm, 105 grams
>     Operating System MikroTik RouterOS v3, Level5 license
>     Actual tested throughput
>         Ether1 <-> Ether2 = 1Gbps
>         Ether2 <-> Ether3 = 650Mbps
> 
> openvrt/debvrt support this board
> 
> (no FPU)
> 
> Oliver 
> 
> > On Thu, Aug 02, 2012 at 05:25:13PM +0300, Kaj-Michael Lang wrote:
> > 
> > > On Thu, 2012-07-19 at 21:15 +0200, Oliver Kowalke wrote:
> > > > I'm searching for an development board with a MIPS processor - 1GB
> > > > RAM 
> > > > would be nice but 10/100MBit ethernet is required. 
> > > 
> > > Don't know about the ethernet part, but you could check out the very
> > > cheap mips based android tablets. Search for Ainol Novo 7 Paladin for
> > > example, under 100€.
> > > 
> > > Anyone tried getting plain-old-linux running on one?
> > 
> > I suggest that whoever has suggestions for suitable boards should list
> > them including key technical data such as kernel / distribution support,
> > CPU type, 32/64 bit, endianess, price, peripherals, manufacturing status
> > and availability.
> > 
> >   Ralf
> > 
> 

<Prev in Thread] Current Thread [Next in Thread>