linux-mips
[Top] [All Lists]

[PATCH 2/4] netdev/phy/of: Handle IEEE802.3 clause 45 Ethernet PHYs in o

To: Grant Likely <grant.likely@secretlab.ca>, Rob Herring <rob.herring@calxeda.com>, devicetree-discuss@lists.ozlabs.org, "David S. Miller" <davem@davemloft.net>, netdev@vger.kernel.org
Subject: [PATCH 2/4] netdev/phy/of: Handle IEEE802.3 clause 45 Ethernet PHYs in of_mdiobus_register()
From: David Daney <ddaney.cavm@gmail.com>
Date: Fri, 22 Jun 2012 17:24:14 -0700
Cc: linux-kernel@vger.kernel.org, linux-mips@linux-mips.org, afleming@gmail.com, David Daney <david.daney@cavium.com>
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=20120113; h=from:to:cc:subject:date:message-id:x-mailer:in-reply-to:references; bh=RHvqQy/RH49RjiILcFyOG//jPk+Bo2ykTpXQf47yTTk=; b=st2jxv54gHB2Na8I0EiaodzsSz9p1u7XJWp4Ev7DrGlvoYuwIR4YxcraPTX1d3CxM1 lEqPQyomxeEftyLLsKPdeZt1jlmwg+x0mviJeJ6Vaoqn+crB6FCxOZVjgDDxXc5r46YQ wKx+vYtRwIy8E8kJeLAsTSCoUtYlmxa/wtIGuu2IFIi2szNy5UghWddJSwxlUo/U7fW3 aLepABNbjrrvJoCV3K2VD7aaQJyHBmUwcT3ufLAw+/ZwJcKCZ1K0ZyqzybKVS6893zW+ dhiJIpnu8Y3ORSO5A04aI7Y1kmQyPkoOvt2h/E4+NZysw0eSJuA/vH2XIddOBopXuRaS Zq4w==
In-reply-to: <1340411056-18988-1-git-send-email-ddaney.cavm@gmail.com>
List-archive: <http://www.linux-mips.org/archives/linux-mips/>
List-help: <mailto:ecartis@linux-mips.org?Subject=help>
List-id: linux-mips <linux-mips.eddie.linux-mips.org>
List-owner: <mailto:ralf@linux-mips.org>
List-post: <mailto:linux-mips@linux-mips.org>
List-software: Ecartis version 1.0.0
List-subscribe: <mailto:ecartis@linux-mips.org?subject=subscribe%20linux-mips>
List-unsubscribe: <mailto:ecartis@linux-mips.org?subject=unsubscribe%20linux-mips>
References: <1340411056-18988-1-git-send-email-ddaney.cavm@gmail.com>
Sender: linux-mips-bounce@linux-mips.org
From: David Daney <david.daney@cavium.com>

Define two new "compatible" values for Ethernet
PHYs. "ethernet-phy-ieee802.3-c22" and "ethernet-phy-ieee802.3-c45"
are used to indicate a PHY uses the corresponding protocol.

If a PHY is "compatible" with "ethernet-phy-ieee802.3-c45", we
indicate this so that get_phy_device() can properly probe the device.

If get_phy_device() fails, it was probably due to failing the probe of
the PHY identifier registers.  Since we have the device tree telling
us the PHY exists, go ahead and add it anyhow with a phy_id of zero.
There may be a driver match based on the "compatible" property.

Signed-off-by: David Daney <david.daney@cavium.com>
---
 Documentation/devicetree/bindings/net/phy.txt |   12 +++++++++++-
 drivers/of/of_mdio.c                          |   14 +++++++++++---
 2 files changed, 22 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/phy.txt 
b/Documentation/devicetree/bindings/net/phy.txt
index bb8c742..7cd18fb 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -14,10 +14,20 @@ Required properties:
  - linux,phandle :  phandle for this node; likely referenced by an
    ethernet controller node.
 
+Optional Properties:
+
+- compatible: Compatible list, may contain
+  "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for
+  PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45
+  specifications. If neither of these are specified, the default is to
+  assume clause 22. The compatible list may also contain other
+  elements.
+
 Example:
 
 ethernet-phy@0 {
-       linux,phandle = <2452000>
+       compatible = "ethernet-phy-ieee802.3-c22";
+       linux,phandle = <2452000>;
        interrupt-parent = <40000>;
        interrupts = <35 1>;
        reg = <0>;
diff --git a/drivers/of/of_mdio.c b/drivers/of/of_mdio.c
index 2574abd..0f08aaf 100644
--- a/drivers/of/of_mdio.c
+++ b/drivers/of/of_mdio.c
@@ -79,11 +79,19 @@ int of_mdiobus_register(struct mii_bus *mdio, struct 
device_node *np)
                                mdio->irq[addr] = PHY_POLL;
                }
 
+               if (of_device_is_compatible(child,
+                                           "ethernet-phy-ieee802.3-c45"))
+                       addr |= MII_ADDR_C45;
+
                phy = get_phy_device(mdio, addr);
                if (!phy || IS_ERR(phy)) {
-                       dev_err(&mdio->dev, "error probing PHY at address %i\n",
-                               addr);
-                       continue;
+                       phy = phy_device_create(mdio, addr, 0, NULL);
+                       if (!phy || IS_ERR(phy)) {
+                               dev_err(&mdio->dev,
+                                       "error creating PHY at address %i\n",
+                                       addr);
+                               continue;
+                       }
                }
 
                /* Associate the OF node with the device structure so it
-- 
1.7.2.3


<Prev in Thread] Current Thread [Next in Thread>