linux-mips
[Top] [All Lists]

NXP STB225 board support

To: linux-mips@linux-mips.org
Subject: NXP STB225 board support
From: "Ihar Hrachyshka" <ihar.hrachyshka@gmail.com>
Date: Tue, 23 Dec 2008 16:48:23 +0200
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=gmail.com; s=gamma; h=domainkey-signature:received:received:message-id:date:from:to :subject:mime-version:content-type:content-transfer-encoding :content-disposition; bh=Ao1JkekF52YNF6/P4rjvooYYfjQACztCdME/7PRhV50=; b=b/EV6dDmlhIXnBe1IvkeLGXqzPpmG82GkbSS0fWlE4knL7tavHI44f261qnfonhc1q 6nUxEIXEmGjxKaFD9CLvOG8NUA0vGSmnXL1AvRCY6jUc/AIvL/wwiL8RkECZzWqp+Kkj Nsyx/DbLgDa8LYbVGcpLEtkPQ7k7CS6hp+Pu4=
Domainkey-signature: a=rsa-sha1; c=nofws; d=gmail.com; s=gamma; h=message-id:date:from:to:subject:mime-version:content-type :content-transfer-encoding:content-disposition; b=DZyWg4LNNzL4GfkQ5CzjIRzJLapizThBpPB8+kT4ix0JwjhBhFZRbupAw+n+m8fCCp 8cQzpzqhLtKCM5UxNOXBpDeJ2ScbKR02KFe7jm8GXAP4RBAggF21pYOWk4m8vlpnC7Qz jv5tDTuqpUWWGR4QolLPleK9DVXgOD/athvZ0=
Original-recipient: rfc822;linux-mips@linux-mips.org
Sender: linux-mips-bounce@linux-mips.org
Hello!
I try to start vanilla linux kernel on pnx-8335-stb225 board. What I did:
1. ARCH=mips make pnx-8335-stb225_defconfig
2. ARCH=mips make
3. Prepared U-Boot image with mkimage.

After booting it up I get the following output on my UART:

Linux version 2.6.28-rc9.netflix.PR12_RC2 (booxter@EPBYMINW0568) (gcc
version 4.2.1) #3 PREEMPT Tue Dec 23 15:52:10 EET 2008
CPU revision is: 00019068 (MIPS 4KEc)
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00010000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00010000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line:
mtdparts=gen_nand:128k(Boot0),1M(Boot1),512k(Env),4M(Kernel),16M(Filesystem)
ip3902.mac_address=00:60:37:03:00:00 ip=10.6.2.53:10.6.27.3
Unknown boot option `ip3902.mac_address=00:60:37:03:00:00': ignoring
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
PID hash table entries: 1024 (order: 10, 4096 bytes)
CPU clock is 320 MHz
Console: colour dummy device 80x25
console [ttyS0] enabled

After this last message there is no any activity. It seems that kernel
hanged. What can I do to see what's going on (maybe stack trace)? Any
suggestions?
Has anyone started the board successfully with vanilla kernel?

Thanks in advance,
Ihar Hrachyshka

<Prev in Thread] Current Thread [Next in Thread>
  • NXP STB225 board support, Ihar Hrachyshka <=