linux-mips
[Top] [All Lists]

[PATCH 2/2] MIPS: Add Cavium OCTEON PCI support.

To: linux-mips@linux-mips.org
Subject: [PATCH 2/2] MIPS: Add Cavium OCTEON PCI support.
From: David Daney <ddaney@caviumnetworks.com>
Date: Fri, 19 Dec 2008 15:20:28 -0800
Cc: David Daney <ddaney@caviumnetworks.com>
In-reply-to: <494C2BC1.2080903@caviumnetworks.com>
Original-recipient: rfc822;linux-mips@linux-mips.org
References: <494C2BC1.2080903@caviumnetworks.com>
Sender: linux-mips-bounce@linux-mips.org
This patch adds support for PCI and PCIe to the base Cavium OCTEON
processor support.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
---
 arch/mips/Kconfig                                  |    2 +
 arch/mips/cavium-octeon/Makefile                   |    4 +
 arch/mips/cavium-octeon/dma-octeon.c               |  310 ++++++-
 arch/mips/cavium-octeon/executive/Makefile         |    2 +
 .../cavium-octeon/executive/cvmx-helper-errata.c   |  379 +++++++
 .../cavium-octeon/executive/cvmx-helper-util.c     |  502 ++++++++++
 arch/mips/cavium-octeon/executive/cvmx-pcie.c      | 1053 ++++++++++++++++++++
 arch/mips/cavium-octeon/msi.c                      |  288 ++++++
 arch/mips/cavium-octeon/octeon-irq.c               |    2 +
 arch/mips/cavium-octeon/pci-common.c               |  137 +++
 arch/mips/cavium-octeon/pci-common.h               |   39 +
 arch/mips/cavium-octeon/pci.c                      |  568 +++++++++++
 arch/mips/cavium-octeon/pcie.c                     |  441 ++++++++
 arch/mips/include/asm/octeon/cvmx-asm.h            |    3 +-
 arch/mips/include/asm/octeon/cvmx-helper-errata.h  |   92 ++
 arch/mips/include/asm/octeon/cvmx-helper-util.h    |  266 +++++
 arch/mips/include/asm/octeon/cvmx-packet.h         |   16 +-
 arch/mips/include/asm/octeon/cvmx-pcie.h           |  284 ++++++
 arch/mips/include/asm/octeon/cvmx-wqe.h            |  422 ++++++++
 arch/mips/include/asm/octeon/cvmx.h                |   12 +
 arch/mips/include/asm/octeon/octeon.h              |    2 +
 21 files changed, 4816 insertions(+), 8 deletions(-)
 create mode 100644 arch/mips/cavium-octeon/executive/cvmx-helper-errata.c
 create mode 100644 arch/mips/cavium-octeon/executive/cvmx-helper-util.c
 create mode 100644 arch/mips/cavium-octeon/executive/cvmx-pcie.c
 create mode 100644 arch/mips/cavium-octeon/msi.c
 create mode 100644 arch/mips/cavium-octeon/pci-common.c
 create mode 100644 arch/mips/cavium-octeon/pci-common.h
 create mode 100644 arch/mips/cavium-octeon/pci.c
 create mode 100644 arch/mips/cavium-octeon/pcie.c
 create mode 100644 arch/mips/include/asm/octeon/cvmx-helper-errata.h
 create mode 100644 arch/mips/include/asm/octeon/cvmx-helper-util.h
 create mode 100644 arch/mips/include/asm/octeon/cvmx-pcie.h
 create mode 100644 arch/mips/include/asm/octeon/cvmx-wqe.h

diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index ea2b262..f009496 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -620,6 +620,8 @@ config CAVIUM_OCTEON_REFERENCE_BOARD
        select SYS_HAS_EARLY_PRINTK
        select CPU_CAVIUM_OCTEON
        select SWAP_IO_SPACE
+       select HW_HAS_PCI
+       select ARCH_SUPPORTS_MSI
        help
          This option supports all of the Octeon reference boards from Cavium
          Networks. It builds a kernel that dynamically determines the Octeon
diff --git a/arch/mips/cavium-octeon/Makefile b/arch/mips/cavium-octeon/Makefile
index 1c2a7fa..2b5f08f 100644
--- a/arch/mips/cavium-octeon/Makefile
+++ b/arch/mips/cavium-octeon/Makefile
@@ -14,3 +14,7 @@ obj-y += dma-octeon.o flash_setup.o
 obj-y += octeon-memcpy.o
 
 obj-$(CONFIG_SMP)                     += smp.o
+obj-$(CONFIG_PCI)                     += pci-common.o
+obj-$(CONFIG_PCI)                     += pci.o
+obj-$(CONFIG_PCI)                     += pcie.o
+obj-$(CONFIG_PCI_MSI)                 += msi.o
diff --git a/arch/mips/cavium-octeon/dma-octeon.c 
b/arch/mips/cavium-octeon/dma-octeon.c
index 01b1ef9..af3c26f 100644
--- a/arch/mips/cavium-octeon/dma-octeon.c
+++ b/arch/mips/cavium-octeon/dma-octeon.c
@@ -13,20 +13,326 @@
  */
 #include <linux/types.h>
 #include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/scatterlist.h>
+
+#include <linux/cache.h>
+#include <linux/io.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-pci-defs.h>
 
 #include <dma-coherence.h>
 
+#ifdef CONFIG_PCI
+#include "pci-common.h"
+#endif
+
+#define BAR2_PCI_ADDRESS 0x8000000000ul
+
+struct bar1_index_state {
+       int16_t ref_count;      /* Number of PCI mappings using this index */
+       uint16_t address_bits;  /* Upper bits of physical address. This is
+                                  shifted 22 bits */
+};
+
+#ifdef CONFIG_PCI
+static DEFINE_SPINLOCK(bar1_lock);
+static struct bar1_index_state bar1_state[32];
+#endif
+
 dma_addr_t octeon_map_dma_mem(struct device *dev, void *ptr, size_t size)
 {
+#ifndef CONFIG_PCI
        /* Without PCI/PCIe this function can be called for Octeon internal
           devices such as USB. These devices all support 64bit addressing */
        mb();
        return virt_to_phys(ptr);
+#else
+       unsigned long flags;
+       uint64_t dma_mask;
+       int64_t start_index;
+       dma_addr_t result = -1;
+       uint64_t physical = virt_to_phys(ptr);
+       int64_t index;
+
+       mb();
+       /*
+        * Use the DMA masks to determine the allowed memory
+        * region. For us it doesn't limit the actual memory, just the
+        * address visible over PCI.  Devices with limits need to use
+        * lower indexed Bar1 entries.
+        */
+       if (dev) {
+               dma_mask = dev->coherent_dma_mask;
+               if (dev->dma_mask)
+                       dma_mask = *dev->dma_mask;
+       } else
+               dma_mask = 0xfffffffful;
+
+       /*
+        * Platform devices, such as the internal USB, skip all
+        * translation and use Octeon physical addresses directly.
+        */
+       if (dev->bus == &platform_bus_type)
+               return physical;
+
+       switch (octeon_dma_bar_type) {
+       case OCTEON_DMA_BAR_TYPE_PCIE:
+               if (unlikely(physical < (16ul << 10)))
+                       panic("dma_map_single: Not allowed to map first 16KB."
+                             " It interferes with BAR0 special area\n");
+               else if ((physical + size >= (256ul << 20)) &&
+                        (physical < (512ul << 20)))
+                       panic("dma_map_single: Not allowed to map bootbus\n");
+               else if ((physical + size >= 0x400000000ull) &&
+                        physical < 0x410000000ull)
+                       panic("dma_map_single: "
+                             "Attempt to map illegal memory address 0x%lx\n",
+                             physical);
+               else if (physical >= 0x420000000ull)
+                       panic("dma_map_single: "
+                             "Attempt to map illegal memory address 0x%lx\n",
+                             physical);
+               else if ((physical + size >=
+                         (4ull<<30) - (OCTEON_PCI_BAR1_HOLE_SIZE<<20))
+                        && physical < (4ull<<30))
+                       pr_warning("dma_map_single: Warning: "
+                                  "Mapping memory address that might "
+                                  "conflict with devices 0x%lx-0x%lx\n",
+                                  physical, physical+size-1);
+               /* The 2nd 256MB is mapped at 256<<20 instead of 0x410000000 */
+               if ((physical >= 0x410000000ull) && physical < 0x420000000ull)
+                       result = physical - 0x400000000ull;
+               else
+                       result = physical;
+               if (((result+size-1) & dma_mask) != result+size-1)
+                       panic("dma_map_single: Attempt to map address "
+                             "0x%lx-0x%lx, which can't be accessed according "
+                             "to the dma mask 0x%lx\n",
+                             physical, physical+size-1, dma_mask);
+               goto done;
+
+       case OCTEON_DMA_BAR_TYPE_BIG:
+#ifdef CONFIG_64BIT
+               /* If the device supports 64bit addressing, then use BAR2 */
+               if (dma_mask > BAR2_PCI_ADDRESS) {
+                       result = physical + BAR2_PCI_ADDRESS;
+                       goto done;
+               }
+#endif
+               if (unlikely(physical < (4ul << 10))) {
+                       panic("dma_map_single: Not allowed to map first 4KB. "
+                             "It interferes with BAR0 special area\n");
+               } else if (physical < (256ul << 20)) {
+                       if (unlikely(physical + size > (256ul << 20)))
+                               panic("dma_map_single: Requested memory spans "
+                                     "Bar0 0:256MB and bootbus\n");
+                       result = physical;
+                       goto done;
+               } else if (unlikely(physical < (512ul << 20))) {
+                       panic("dma_map_single: Not allowed to map bootbus\n");
+               } else if (physical < (2ul << 30)) {
+                       if (unlikely(physical + size > (2ul << 30)))
+                               panic("dma_map_single: Requested memory spans "
+                                     "Bar0 512MB:2GB and BAR1\n");
+                       result = physical;
+                       goto done;
+               } else if (physical < (2ul << 30) + (128 << 20)) {
+                       /* Fall through */
+               } else if (physical <
+                          (4ul << 30) - (OCTEON_PCI_BAR1_HOLE_SIZE << 20)) {
+                       if (unlikely
+                           (physical + size >
+                            (4ul << 30) - (OCTEON_PCI_BAR1_HOLE_SIZE << 20)))
+                               panic("dma_map_single: Requested memory "
+                                     "extends past Bar1 (4GB-%luMB)\n",
+                                     OCTEON_PCI_BAR1_HOLE_SIZE);
+                       result = physical;
+                       goto done;
+               } else if ((physical >= 0x410000000ull) &&
+                          (physical < 0x420000000ull)) {
+                       if (unlikely(physical + size > 0x420000000ull))
+                               panic("dma_map_single: Requested memory spans "
+                                     "non existant memory\n");
+                       /* BAR0 fixed mapping 256MB:512MB ->
+                        * 16GB+256MB:16GB+512MB */
+                       result = physical - 0x400000000ull;
+                       goto done;
+               } else {
+                       /* Continued below switch statement */
+               }
+               break;
+
+       case OCTEON_DMA_BAR_TYPE_SMALL:
+#ifdef CONFIG_64BIT
+               /* If the device supports 64bit addressing, then use BAR2 */
+               if (dma_mask > BAR2_PCI_ADDRESS) {
+                       result = physical + BAR2_PCI_ADDRESS;
+                       goto done;
+               }
+#endif
+               /* Continued below switch statement */
+               break;
+
+       default:
+               panic("dma_map_single: Invalid octeon_dma_bar_type\n");
+       }
+
+       /* Don't allow mapping to span multiple Bar entries. The hardware guys
+          won't guarantee that DMA across boards work */
+       if (unlikely((physical >> 22) != ((physical + size - 1) >> 22)))
+               panic("dma_map_single: "
+                     "Requested memory spans more than one Bar1 entry\n");
+
+       if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG)
+               start_index = 31;
+       else if (unlikely(dma_mask < (1ul << 27)))
+               start_index = (dma_mask >> 22);
+       else
+               start_index = 31;
+
+       /* Only one processor can access the Bar register at once */
+       spin_lock_irqsave(&bar1_lock, flags);
+
+       /* Look through Bar1 for existing mapping that will work */
+       for (index = start_index; index >= 0; index--) {
+               if ((bar1_state[index].address_bits == physical >> 22) &&
+                   (bar1_state[index].ref_count)) {
+                       /* An existing mapping will work, use it */
+                       bar1_state[index].ref_count++;
+                       if (unlikely(bar1_state[index].ref_count < 0))
+                               panic("dma_map_single: "
+                                     "Bar1[%d] reference count overflowed\n",
+                                     (int) index);
+                       result = (index << 22) | (physical & ((1 << 22) - 1));
+                       /* Large BAR1 is offset at 2GB */
+                       if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG)
+                               result += 2ul << 30;
+                       goto done_unlock;
+               }
+       }
+
+       /* No existing mappings, look for a free entry */
+       for (index = start_index; index >= 0; index--) {
+               if (unlikely(bar1_state[index].ref_count == 0)) {
+                       union cvmx_pci_bar1_indexx bar1_index;
+                       /* We have a free entry, use it */
+                       bar1_state[index].ref_count = 1;
+                       bar1_state[index].address_bits = physical >> 22;
+                       bar1_index.u32 = 0;
+                       /* Address bits[35:22] sent to L2C */
+                       bar1_index.s.addr_idx = physical >> 22;
+                       /* Don't put PCI accesses in L2. */
+                       bar1_index.s.ca = 1;
+                       /* Endian Swap Mode */
+                       bar1_index.s.end_swp = 1;
+                       /* Set '1' when the selected address range is valid. */
+                       bar1_index.s.addr_v = 1;
+                       octeon_npi_write32(CVMX_NPI_PCI_BAR1_INDEXX(index),
+                                          bar1_index.u32);
+                       /* An existing mapping will work, use it */
+                       result = (index << 22) | (physical & ((1 << 22) - 1));
+                       /* Large BAR1 is offset at 2GB */
+                       if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG)
+                               result += 2ul << 30;
+                       goto done_unlock;
+               }
+       }
+
+       pr_err("dma_map_single: "
+              "Can't find empty BAR1 index for physical mapping 0x%llx\n",
+              (unsigned long long) physical);
+
+done_unlock:
+       spin_unlock_irqrestore(&bar1_lock, flags);
+done:
+       pr_debug("dma_map_single 0x%lx->0x%lx\n", physical, result);
+       return result;
+#endif
 }
 
 void octeon_unmap_dma_mem(struct device *dev, dma_addr_t dma_addr)
 {
-       /* Without PCI/PCIe this function can be called for Octeon internal
-        * devices such as USB. These devices all support 64bit addressing */
+#ifndef CONFIG_PCI
+       /*
+        * Without PCI/PCIe this function can be called for Octeon internal
+        * devices such as USB. These devices all support 64bit addressing.
+        */
+       return;
+#else
+       unsigned long flags;
+       uint64_t index;
+
+       /*
+        * Platform devices, such as the internal USB, skip all
+        * translation and use Octeon physical addresses directly.
+        */
+       if (dev->bus == &platform_bus_type)
+               return;
+
+       switch (octeon_dma_bar_type) {
+       case OCTEON_DMA_BAR_TYPE_PCIE:
+               /* Nothing to do, all mappings are static */
+               goto done;
+
+       case OCTEON_DMA_BAR_TYPE_BIG:
+#ifdef CONFIG_64BIT
+               /* Nothing to do for addresses using BAR2 */
+               if (dma_addr >= BAR2_PCI_ADDRESS)
+                       goto done;
+#endif
+               if (unlikely(dma_addr < (4ul << 10)))
+                       panic("dma_unmap_single: Unexpect DMA address 0x%lx\n",
+                             dma_addr);
+               else if (dma_addr < (2ul << 30))
+                       /* Nothing to do for addresses using BAR0 */
+                       goto done;
+               else if (dma_addr < (2ul << 30) + (128ul << 20))
+                       /* Need to unmap, fall through */
+                       index = (dma_addr - (2ul << 30)) >> 22;
+               else if (dma_addr <
+                        (4ul << 30) - (OCTEON_PCI_BAR1_HOLE_SIZE << 20))
+                       goto done;      /* Nothing to do for the rest of BAR1 */
+               else
+                       panic("dma_unmap_single: Unexpect DMA address 0x%lx\n",
+                             dma_addr);
+               /* Continued below switch statement */
+               break;
+
+       case OCTEON_DMA_BAR_TYPE_SMALL:
+#ifdef CONFIG_64BIT
+               /* Nothing to do for addresses using BAR2 */
+               if (dma_addr >= BAR2_PCI_ADDRESS)
+                       goto done;
+#endif
+               index = dma_addr >> 22;
+               /* Continued below switch statement */
+               break;
+
+       default:
+               panic("dma_unmap_single: Invalid octeon_dma_bar_type\n");
+       }
+
+       if (unlikely(index > 31))
+               panic("dma_unmap_single: "
+                     "Attempt to unmap an invalid address (0x%llx)\n",
+                     (unsigned long long) dma_addr);
+
+       spin_lock_irqsave(&bar1_lock, flags);
+       bar1_state[index].ref_count--;
+       if (bar1_state[index].ref_count == 0)
+               octeon_npi_write32(CVMX_NPI_PCI_BAR1_INDEXX(index), 0);
+       else if (unlikely(bar1_state[index].ref_count < 0))
+               panic("dma_unmap_single: Bar1[%u] reference count < 0\n",
+                     (int) index);
+       spin_unlock_irqrestore(&bar1_lock, flags);
+done:
+       pr_debug("dma_unmap_single 0x%lx\n", dma_addr);
        return;
+#endif
 }
diff --git a/arch/mips/cavium-octeon/executive/Makefile 
b/arch/mips/cavium-octeon/executive/Makefile
index 80d6cb2..9b470dd 100644
--- a/arch/mips/cavium-octeon/executive/Makefile
+++ b/arch/mips/cavium-octeon/executive/Makefile
@@ -11,3 +11,5 @@
 
 obj-y += cvmx-bootmem.o cvmx-l2c.o cvmx-sysinfo.o octeon-model.o
 
+obj-$(CONFIG_PCI) += cvmx-pcie.o
+obj-$(CONFIG_PCI) += cvmx-helper-errata.o cvmx-helper-util.o
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-errata.c 
b/arch/mips/cavium-octeon/executive/cvmx-helper-errata.c
new file mode 100644
index 0000000..98822c1
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-errata.c
@@ -0,0 +1,379 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Fixes and workaround for Octeon chip errata. This file
+ * contains functions called by cvmx-helper to workaround known
+ * chip errata. For the most part, code doesn't need to call
+ * these functions directly.
+ *
+ */
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-helper-util.h>
+
+#ifdef CVMX_ENABLE_PKO_FUNCTIONS
+
+/**
+ * @INTERNAL
+ * Function to adjust internal IPD pointer alignments
+ *
+ * Returns 0 on success
+ *         !0 on failure
+ */
+int __cvmx_helper_errata_fix_ipd_ptr_alignment(void)
+{
+#define FIX_IPD_FIRST_BUFF_PAYLOAD_BYTES \
+       (CVMX_FPA_PACKET_POOL_SIZE - 8 - CVMX_HELPER_FIRST_MBUFF_SKIP)
+#define FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES \
+       (CVMX_FPA_PACKET_POOL_SIZE - 8 - CVMX_HELPER_NOT_FIRST_MBUFF_SKIP)
+#define FIX_IPD_OUTPORT 0
+       /* Ports 0-15 are interface 0, 16-31 are interface 1 */
+#define INTERFACE(port) (port >> 4)
+#define INDEX(port) (port & 0xf)
+       uint64_t *p64;
+       cvmx_pko_command_word0_t pko_command;
+       cvmx_buf_ptr_t g_buffer, pkt_buffer;
+       cvmx_wqe_t *work;
+       int size, num_segs = 0, wqe_pcnt, pkt_pcnt;
+       cvmx_gmxx_prtx_cfg_t gmx_cfg;
+       int retry_cnt;
+       int retry_loop_cnt;
+       int mtu;
+       int i;
+       cvmx_helper_link_info_t link_info;
+
+       /* Save values for restore at end */
+       uint64_t prtx_cfg =
+           cvmx_read_csr(CVMX_GMXX_PRTX_CFG(INDEX(FIX_IPD_OUTPORT),
+                                            INTERFACE(FIX_IPD_OUTPORT)));
+       uint64_t tx_ptr_en =
+           cvmx_read_csr(CVMX_ASXX_TX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)));
+       uint64_t rx_ptr_en =
+           cvmx_read_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)));
+       uint64_t rxx_jabber =
+           cvmx_read_csr(CVMX_GMXX_RXX_JABBER(INDEX(FIX_IPD_OUTPORT),
+                                              INTERFACE(FIX_IPD_OUTPORT)));
+       uint64_t frame_max =
+           cvmx_read_csr(CVMX_GMXX_RXX_FRM_MAX(INDEX(FIX_IPD_OUTPORT),
+                                               INTERFACE(FIX_IPD_OUTPORT)));
+
+       /* Configure port to gig FDX as required for loopback mode */
+       cvmx_helper_rgmii_internal_loopback(FIX_IPD_OUTPORT);
+
+       /*
+        * Disable reception on all ports so if traffic is present it
+        * will not interfere.
+        */
+       cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)), 0);
+
+       cvmx_wait(100000000ull);
+
+       for (retry_loop_cnt = 0; retry_loop_cnt < 10; retry_loop_cnt++) {
+               retry_cnt = 100000;
+               wqe_pcnt = cvmx_read_csr(CVMX_IPD_PTR_COUNT);
+               pkt_pcnt = (wqe_pcnt >> 7) & 0x7f;
+               wqe_pcnt &= 0x7f;
+
+               num_segs = (2 + pkt_pcnt - wqe_pcnt) & 3;
+
+               if (num_segs == 0)
+                       goto fix_ipd_exit;
+
+               num_segs += 1;
+
+               size =
+                   FIX_IPD_FIRST_BUFF_PAYLOAD_BYTES +
+                   ((num_segs - 1) * FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES) -
+                   (FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES / 2);
+
+               cvmx_write_csr(CVMX_ASXX_PRT_LOOP(INTERFACE(FIX_IPD_OUTPORT)),
+                              1 << INDEX(FIX_IPD_OUTPORT));
+               CVMX_SYNC;
+
+               g_buffer.u64 = 0;
+               g_buffer.s.addr =
+                   cvmx_ptr_to_phys(cvmx_fpa_alloc(CVMX_FPA_WQE_POOL));
+               if (g_buffer.s.addr == 0) {
+                       cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT buffer "
+                                    "allocation failure.\n");
+                       goto fix_ipd_exit;
+               }
+
+               g_buffer.s.pool = CVMX_FPA_WQE_POOL;
+               g_buffer.s.size = num_segs;
+
+               pkt_buffer.u64 = 0;
+               pkt_buffer.s.addr =
+                   cvmx_ptr_to_phys(cvmx_fpa_alloc(CVMX_FPA_PACKET_POOL));
+               if (pkt_buffer.s.addr == 0) {
+                       cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT buffer "
+                                    "allocation failure.\n");
+                       goto fix_ipd_exit;
+               }
+               pkt_buffer.s.i = 1;
+               pkt_buffer.s.pool = CVMX_FPA_PACKET_POOL;
+               pkt_buffer.s.size = FIX_IPD_FIRST_BUFF_PAYLOAD_BYTES;
+
+               p64 = (uint64_t *) cvmx_phys_to_ptr(pkt_buffer.s.addr);
+               p64[0] = 0xffffffffffff0000ull;
+               p64[1] = 0x08004510ull;
+               p64[2] = ((uint64_t) (size - 14) << 48) | 0x5ae740004000ull;
+               p64[3] = 0x3a5fc0a81073c0a8ull;
+
+               for (i = 0; i < num_segs; i++) {
+                       if (i > 0)
+                               pkt_buffer.s.size =
+                                   FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES;
+
+                       if (i == (num_segs - 1))
+                               pkt_buffer.s.i = 0;
+
+                       *(uint64_t *) cvmx_phys_to_ptr(g_buffer.s.addr +
+                                                      8 * i) = pkt_buffer.u64;
+               }
+
+               /* Build the PKO command */
+               pko_command.u64 = 0;
+               pko_command.s.segs = num_segs;
+               pko_command.s.total_bytes = size;
+               pko_command.s.dontfree = 0;
+               pko_command.s.gather = 1;
+
+               gmx_cfg.u64 =
+                   cvmx_read_csr(CVMX_GMXX_PRTX_CFG
+                                 (INDEX(FIX_IPD_OUTPORT),
+                                  INTERFACE(FIX_IPD_OUTPORT)));
+               gmx_cfg.s.en = 1;
+               cvmx_write_csr(CVMX_GMXX_PRTX_CFG
+                              (INDEX(FIX_IPD_OUTPORT),
+                               INTERFACE(FIX_IPD_OUTPORT)), gmx_cfg.u64);
+               cvmx_write_csr(CVMX_ASXX_TX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+                              1 << INDEX(FIX_IPD_OUTPORT));
+               cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+                              1 << INDEX(FIX_IPD_OUTPORT));
+
+               mtu =
+                   cvmx_read_csr(CVMX_GMXX_RXX_JABBER
+                                 (INDEX(FIX_IPD_OUTPORT),
+                                  INTERFACE(FIX_IPD_OUTPORT)));
+               cvmx_write_csr(CVMX_GMXX_RXX_JABBER
+                              (INDEX(FIX_IPD_OUTPORT),
+                               INTERFACE(FIX_IPD_OUTPORT)), 65392 - 14 - 4);
+               cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX
+                              (INDEX(FIX_IPD_OUTPORT),
+                               INTERFACE(FIX_IPD_OUTPORT)), 65392 - 14 - 4);
+
+#if CVMX_PKO_USE_FAU_FOR_OUTPUT_QUEUES
+               cvmx_pko_send_packet_prepare(FIX_IPD_OUTPORT,
+                                            cvmx_pko_get_base_queue
+                                            (FIX_IPD_OUTPORT),
+                                            CVMX_PKO_LOCK_NONE);
+               cvmx_pko_send_packet_finish(FIX_IPD_OUTPORT,
+                                           cvmx_pko_get_base_queue
+                                           (FIX_IPD_OUTPORT), pko_command,
+                                           g_buffer, CVMX_PKO_LOCK_NONE);
+#else
+               cvmx_pko_send_packet_prepare(FIX_IPD_OUTPORT,
+                                            cvmx_pko_get_base_queue
+                                            (FIX_IPD_OUTPORT),
+                                            CVMX_PKO_LOCK_CMD_QUEUE);
+               cvmx_pko_send_packet_finish(FIX_IPD_OUTPORT,
+                                           cvmx_pko_get_base_queue
+                                           (FIX_IPD_OUTPORT), pko_command,
+                                           g_buffer, CVMX_PKO_LOCK_CMD_QUEUE);
+#endif
+               CVMX_SYNC;
+
+               do {
+                       work = cvmx_pow_work_request_sync(CVMX_POW_WAIT);
+                       retry_cnt--;
+               } while ((work == NULL) && (retry_cnt > 0));
+
+               if (!retry_cnt)
+                       cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT "
+                                    "get_work() timeout occured.\n");
+
+               /* Free packet */
+               if (work)
+                       cvmx_helper_free_packet_data(work);
+       }
+
+fix_ipd_exit:
+
+       /* Return CSR configs to saved values */
+       cvmx_write_csr(CVMX_GMXX_PRTX_CFG
+                      (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)),
+                      prtx_cfg);
+       cvmx_write_csr(CVMX_ASXX_TX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+                      tx_ptr_en);
+       cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+                      rx_ptr_en);
+       cvmx_write_csr(CVMX_GMXX_RXX_JABBER
+                      (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)),
+                      rxx_jabber);
+       cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX
+                      (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)),
+                      frame_max);
+       cvmx_write_csr(CVMX_ASXX_PRT_LOOP(INTERFACE(FIX_IPD_OUTPORT)), 0);
+       /* Set link to down so autonegotiation will set it up again */
+       link_info.u64 = 0;
+       cvmx_helper_link_set(FIX_IPD_OUTPORT, link_info);
+
+       /*
+        * Bring the link back up as autonegotiation is not done in
+        * user applications.
+        */
+       cvmx_helper_link_autoconf(FIX_IPD_OUTPORT);
+
+       CVMX_SYNC;
+       if (num_segs)
+               cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT failed.\n");
+
+       return !!num_segs;
+
+}
+
+/**
+ * @INTERNAL
+ * Workaround ASX setup errata with CN38XX pass1
+ *
+ * @interface: Interface to setup
+ * @port:      Port to setup (0..3)
+ * @cpu_clock_hz:
+ *                  Chip frequency in Hertz
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_errata_asx_pass1(int interface, int port, int cpu_clock_hz)
+{
+       /* Set hi water mark as per errata GMX-4 */
+       if (cpu_clock_hz >= 325000000 && cpu_clock_hz < 375000000)
+               cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 12);
+       else if (cpu_clock_hz >= 375000000 && cpu_clock_hz < 437000000)
+               cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 11);
+       else if (cpu_clock_hz >= 437000000 && cpu_clock_hz < 550000000)
+               cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 10);
+       else if (cpu_clock_hz >= 550000000 && cpu_clock_hz < 687000000)
+               cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 9);
+       else
+               cvmx_dprintf("Illegal clock frequency (%d). "
+                            "CVMX_ASXX_TX_HI_WATERX not set\n",
+                            cpu_clock_hz);
+       return 0;
+}
+
+/**
+ * This function needs to be called on all Octeon chips with
+ * errata PKI-100.
+ *
+ * The Size field is 8 too large in WQE and next pointers
+ *
+ *  The Size field generated by IPD is 8 larger than it should
+ *  be. The Size field is <55:40> of both:
+ *      - WORD3 in the work queue entry, and
+ *      - the next buffer pointer (which precedes the packet data
+ *        in each buffer).
+ *
+ * @work:   Work queue entry to fix
+ * Returns Zero on success. Negative on failure
+ */
+int cvmx_helper_fix_ipd_packet_chain(cvmx_wqe_t *work)
+{
+       uint64_t number_buffers = work->word2.s.bufs;
+
+       /* We only need to do this if the work has buffers */
+       if (number_buffers) {
+               cvmx_buf_ptr_t buffer_ptr = work->packet_ptr;
+               /* Check for errata PKI-100 */
+               if ((buffer_ptr.s.pool == 0) &&
+                   (((uint64_t) buffer_ptr.s.size +
+                           ((uint64_t) buffer_ptr.s.back << 7) +
+                           ((uint64_t) buffer_ptr.s.addr & 0x7F)) !=
+                           (CVMX_FPA_PACKET_POOL_SIZE + 8))) {
+                       /* fix is not needed */
+                       return 0;
+               }
+               /* Decrement the work packet pointer */
+               buffer_ptr.s.size -= 8;
+               work->packet_ptr = buffer_ptr;
+
+               /*
+                * Now loop through decrementing the size for each
+                * additional buffer.
+                */
+               while (--number_buffers) {
+                       /* Chain pointers are 8 bytes before the data */
+                       cvmx_buf_ptr_t *ptr =
+                           (cvmx_buf_ptr_t *) 
cvmx_phys_to_ptr(buffer_ptr.s.addr - 8);
+                       buffer_ptr = *ptr;
+                       buffer_ptr.s.size -= 8;
+                       *ptr = buffer_ptr;
+               }
+       }
+       /*
+        * Make sure that these write go out before other operations
+        * such as FPA frees.
+        */
+       CVMX_SYNCWS;
+       return 0;
+}
+
+#endif /* CVMX_ENABLE_PKO_FUNCTIONS */
+
+/**
+ * Due to errata G-720, the 2nd order CDR circuit on CN52XX pass
+ * 1 doesn't work properly. The following code disables 2nd order
+ * CDR for the specified QLM.
+ *
+ * @qlm:    QLM to disable 2nd order CDR for.
+ */
+void __cvmx_helper_errata_qlm_disable_2nd_order_cdr(int qlm)
+{
+       int lane;
+       cvmx_helper_qlm_jtag_init();
+       /* We need to load all four lanes of the QLM, a total of 1072 bits */
+       for (lane = 0; lane < 4; lane++) {
+               /*
+                * Each lane has 268 bits. We need to set
+                * cfg_cdr_incx<67:64> = 3 and cfg_cdr_secord<77> =
+                * 1. All other bits are zero. Bits go in LSB first,
+                * so start off with the zeros for bits <63:0>.
+                */
+               cvmx_helper_qlm_jtag_shift_zeros(qlm, 63 - 0 + 1);
+               /* cfg_cdr_incx<67:64>=3 */
+               cvmx_helper_qlm_jtag_shift(qlm, 67 - 64 + 1, 3);
+               /* Zeros for bits <76:68> */
+               cvmx_helper_qlm_jtag_shift_zeros(qlm, 76 - 68 + 1);
+               /* cfg_cdr_secord<77>=1 */
+               cvmx_helper_qlm_jtag_shift(qlm, 77 - 77 + 1, 1);
+               /* Zeros for bits <267:78> */
+               cvmx_helper_qlm_jtag_shift_zeros(qlm, 267 - 78 + 1);
+       }
+       cvmx_helper_qlm_jtag_update(qlm);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-util.c 
b/arch/mips/cavium-octeon/executive/cvmx-helper-util.c
new file mode 100644
index 0000000..dc0087c
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-util.c
@@ -0,0 +1,502 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Small helper utilities.
+ *
+ */
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-helper-util.h>
+
+#ifdef CVMX_ENABLE_HELPER_FUNCTIONS
+
+/**
+ * Get the version of the CVMX libraries.
+ *
+ * Returns Version string. Note this buffer is allocated statically
+ *         and will be shared by all callers.
+ */
+const char *cvmx_helper_get_version(void)
+{
+       return OCTEON_SDK_VERSION_STRING;
+}
+
+/**
+ * Convert a interface mode into a human readable string
+ *
+ * @mode:   Mode to convert
+ *
+ * Returns String
+ */
+const char *cvmx_helper_interface_mode_to_string(cvmx_helper_interface_mode_t
+                                                mode)
+{
+       switch (mode) {
+       case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+               return "DISABLED";
+       case CVMX_HELPER_INTERFACE_MODE_RGMII:
+               return "RGMII";
+       case CVMX_HELPER_INTERFACE_MODE_GMII:
+               return "GMII";
+       case CVMX_HELPER_INTERFACE_MODE_SPI:
+               return "SPI";
+       case CVMX_HELPER_INTERFACE_MODE_PCIE:
+               return "PCIE";
+       case CVMX_HELPER_INTERFACE_MODE_XAUI:
+               return "XAUI";
+       case CVMX_HELPER_INTERFACE_MODE_SGMII:
+               return "SGMII";
+       case CVMX_HELPER_INTERFACE_MODE_PICMG:
+               return "PICMG";
+       case CVMX_HELPER_INTERFACE_MODE_NPI:
+               return "NPI";
+       case CVMX_HELPER_INTERFACE_MODE_LOOP:
+               return "LOOP";
+       }
+       return "UNKNOWN";
+}
+
+/**
+ * Debug routine to dump the packet structure to the console
+ *
+ * @work:   Work queue entry containing the packet to dump
+ */
+int cvmx_helper_dump_packet(cvmx_wqe_t *work)
+{
+       uint64_t count;
+       uint64_t remaining_bytes;
+       cvmx_buf_ptr_t buffer_ptr;
+       uint64_t start_of_buffer;
+       uint8_t *data_address;
+       uint8_t *end_of_data;
+
+       cvmx_dprintf("Packet Length:   %u\n", work->len);
+       cvmx_dprintf("    Input Port:  %u\n", work->ipprt);
+       cvmx_dprintf("    QoS:         %u\n", work->qos);
+       cvmx_dprintf("    Buffers:     %u\n", work->word2.s.bufs);
+
+       if (work->word2.s.bufs == 0) {
+               cvmx_ipd_wqe_fpa_queue_t wqe_pool;
+               wqe_pool.u64 = cvmx_read_csr(CVMX_IPD_WQE_FPA_QUEUE);
+               buffer_ptr.u64 = 0;
+               buffer_ptr.s.pool = wqe_pool.s.wqe_pool;
+               buffer_ptr.s.size = 128;
+               buffer_ptr.s.addr = cvmx_ptr_to_phys(work->packet_data);
+               if (cvmx_likely(!work->word2.s.not_IP)) {
+                       if (work->word2.s.is_v6)
+                               buffer_ptr.s.addr += 2;
+                       else
+                               buffer_ptr.s.addr += 6;
+               }
+       } else
+               buffer_ptr = work->packet_ptr;
+       remaining_bytes = work->len;
+
+       while (remaining_bytes) {
+               start_of_buffer =
+                   ((buffer_ptr.s.addr >> 7) - buffer_ptr.s.back) << 7;
+               cvmx_dprintf("    Buffer Start:%llx\n",
+                            (unsigned long long)start_of_buffer);
+               cvmx_dprintf("    Buffer I   : %u\n", buffer_ptr.s.i);
+               cvmx_dprintf("    Buffer Back: %u\n", buffer_ptr.s.back);
+               cvmx_dprintf("    Buffer Pool: %u\n", buffer_ptr.s.pool);
+               cvmx_dprintf("    Buffer Data: %llx\n",
+                            (unsigned long long)buffer_ptr.s.addr);
+               cvmx_dprintf("    Buffer Size: %u\n", buffer_ptr.s.size);
+
+               cvmx_dprintf("\t\t");
+               data_address = (uint8_t *) cvmx_phys_to_ptr(buffer_ptr.s.addr);
+               end_of_data = data_address + buffer_ptr.s.size;
+               count = 0;
+               while (data_address < end_of_data) {
+                       if (remaining_bytes == 0)
+                               break;
+                       else
+                               remaining_bytes--;
+                       cvmx_dprintf("%02x", (unsigned int)*data_address);
+                       data_address++;
+                       if (remaining_bytes && (count == 7)) {
+                               cvmx_dprintf("\n\t\t");
+                               count = 0;
+                       } else
+                               count++;
+               }
+               cvmx_dprintf("\n");
+
+               if (remaining_bytes)
+                       buffer_ptr =
+                           *(cvmx_buf_ptr_t *) cvmx_phys_to_ptr(buffer_ptr.s.
+                                                                addr - 8);
+       }
+       return 0;
+}
+
+/**
+ * Setup Random Early Drop on a specific input queue
+ *
+ * @queue:  Input queue to setup RED on (0-7)
+ * @pass_thresh:
+ *               Packets will begin slowly dropping when there are less than
+ *               this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *               All incomming packets will be dropped when there are less
+ *               than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+int cvmx_helper_setup_red_queue(int queue, int pass_thresh, int drop_thresh)
+{
+       cvmx_ipd_qos_red_marks_t red_marks;
+       cvmx_ipd_red_quex_param_t red_param;
+
+       /*
+        * Set RED to begin dropping packets when there are
+        * pass_thresh buffers left. It will linearly drop more
+        * packets until reaching drop_thresh buffers.
+        */
+       red_marks.u64 = 0;
+       red_marks.s.drop = drop_thresh;
+       red_marks.s.pass = pass_thresh;
+       cvmx_write_csr(CVMX_IPD_QOSX_RED_MARKS(queue), red_marks.u64);
+
+       /* Use the actual queue 0 counter, not the average */
+       red_param.u64 = 0;
+       red_param.s.prb_con =
+           (255ul << 24) / (red_marks.s.pass - red_marks.s.drop);
+       red_param.s.avg_con = 1;
+       red_param.s.new_con = 255;
+       red_param.s.use_pcnt = 1;
+       cvmx_write_csr(CVMX_IPD_RED_QUEX_PARAM(queue), red_param.u64);
+       return 0;
+}
+
+/**
+ * Setup Random Early Drop to automatically begin dropping packets.
+ *
+ * @pass_thresh:
+ *               Packets will begin slowly dropping when there are less than
+ *               this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *               All incomming packets will be dropped when there are less
+ *               than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+int cvmx_helper_setup_red(int pass_thresh, int drop_thresh)
+{
+       cvmx_ipd_portx_bp_page_cnt_t page_cnt;
+       cvmx_ipd_bp_prt_red_end_t ipd_bp_prt_red_end;
+       cvmx_ipd_red_port_enable_t red_port_enable;
+       int queue;
+       int interface;
+       int port;
+
+       /* Disable backpressure based on queued buffers. It needs SW support */
+       page_cnt.u64 = 0;
+       page_cnt.s.bp_enb = 0;
+       page_cnt.s.page_cnt = 100;
+       for (interface = 0; interface < 2; interface++) {
+               for (port = cvmx_helper_get_first_ipd_port(interface);
+                    port < cvmx_helper_get_last_ipd_port(interface); port++)
+                       cvmx_write_csr(CVMX_IPD_PORTX_BP_PAGE_CNT(port),
+                                      page_cnt.u64);
+       }
+
+       for (queue = 0; queue < 8; queue++)
+               cvmx_helper_setup_red_queue(queue, pass_thresh, drop_thresh);
+
+       /* Shutoff the dropping based on the per port page count. SW isn't
+          decrementing it right now */
+       ipd_bp_prt_red_end.u64 = 0;
+       ipd_bp_prt_red_end.s.prt_enb = 0;
+       cvmx_write_csr(CVMX_IPD_BP_PRT_RED_END, ipd_bp_prt_red_end.u64);
+
+       red_port_enable.u64 = 0;
+       red_port_enable.s.prt_enb = 0xfffffffffull;
+       red_port_enable.s.avg_dly = 10000;
+       red_port_enable.s.prb_dly = 10000;
+       cvmx_write_csr(CVMX_IPD_RED_PORT_ENABLE, red_port_enable.u64);
+
+       return 0;
+}
+
+/**
+ * Setup the common GMX settings that determine the number of
+ * ports. These setting apply to almost all configurations of all
+ * chips.
+ *
+ * @interface: Interface to configure
+ * @num_ports: Number of ports on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_setup_gmx(int interface, int num_ports)
+{
+       cvmx_gmxx_tx_prts_t gmx_tx_prts;
+       cvmx_gmxx_rx_prts_t gmx_rx_prts;
+       cvmx_pko_reg_gmx_port_mode_t pko_mode;
+
+       /* Tell GMX the number of TX ports on this interface */
+       gmx_tx_prts.u64 = cvmx_read_csr(CVMX_GMXX_TX_PRTS(interface));
+       gmx_tx_prts.s.prts = num_ports;
+       cvmx_write_csr(CVMX_GMXX_TX_PRTS(interface), gmx_tx_prts.u64);
+
+       /*
+        * Tell GMX the number of RX ports on this interface.  This only
+        * applies to *GMII and XAUI ports.
+        */
+       if (cvmx_helper_interface_get_mode(interface) ==
+           CVMX_HELPER_INTERFACE_MODE_RGMII
+           || cvmx_helper_interface_get_mode(interface) ==
+           CVMX_HELPER_INTERFACE_MODE_SGMII
+           || cvmx_helper_interface_get_mode(interface) ==
+           CVMX_HELPER_INTERFACE_MODE_GMII
+           || cvmx_helper_interface_get_mode(interface) ==
+           CVMX_HELPER_INTERFACE_MODE_XAUI) {
+               if (num_ports > 4) {
+                       cvmx_dprintf("__cvmx_helper_setup_gmx: "
+                                    "Illegal num_ports\n");
+                       return -1;
+               }
+
+               gmx_rx_prts.u64 = cvmx_read_csr(CVMX_GMXX_RX_PRTS(interface));
+               gmx_rx_prts.s.prts = num_ports;
+               cvmx_write_csr(CVMX_GMXX_RX_PRTS(interface), gmx_rx_prts.u64);
+       }
+
+       /* Skip setting CVMX_PKO_REG_GMX_PORT_MODE on 30XX and 31XX */
+       if (OCTEON_IS_MODEL(OCTEON_CN30XX) || OCTEON_IS_MODEL(OCTEON_CN31XX)
+           || OCTEON_IS_MODEL(OCTEON_CN50XX))
+               return 0;
+
+       /* Tell PKO the number of ports on this interface */
+       pko_mode.u64 = cvmx_read_csr(CVMX_PKO_REG_GMX_PORT_MODE);
+       if (interface == 0) {
+               if (num_ports == 1)
+                       pko_mode.s.mode0 = 4;
+               else if (num_ports == 2)
+                       pko_mode.s.mode0 = 3;
+               else if (num_ports <= 4)
+                       pko_mode.s.mode0 = 2;
+               else if (num_ports <= 8)
+                       pko_mode.s.mode0 = 1;
+               else
+                       pko_mode.s.mode0 = 0;
+       } else {
+               if (num_ports == 1)
+                       pko_mode.s.mode1 = 4;
+               else if (num_ports == 2)
+                       pko_mode.s.mode1 = 3;
+               else if (num_ports <= 4)
+                       pko_mode.s.mode1 = 2;
+               else if (num_ports <= 8)
+                       pko_mode.s.mode1 = 1;
+               else
+                       pko_mode.s.mode1 = 0;
+       }
+       cvmx_write_csr(CVMX_PKO_REG_GMX_PORT_MODE, pko_mode.u64);
+       return 0;
+}
+
+/**
+ * Returns the IPD/PKO port number for a port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ * @port:      Port on the interface
+ *
+ * Returns IPD/PKO port number
+ */
+int cvmx_helper_get_ipd_port(int interface, int port)
+{
+       switch (interface) {
+       case 0:
+               return port;
+       case 1:
+               return port + 16;
+       case 2:
+               return port + 32;
+       case 3:
+               return port + 36;
+       }
+       return -1;
+}
+
+#endif /* CVMX_ENABLE_HELPER_FUNCTIONS */
+
+/**
+ * Returns the interface number for an IPD/PKO port number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface number
+ */
+int cvmx_helper_get_interface_num(int ipd_port)
+{
+       if (ipd_port < 16)
+               return 0;
+       else if (ipd_port < 32)
+               return 1;
+       else if (ipd_port < 36)
+               return 2;
+       else if (ipd_port < 40)
+               return 3;
+       else
+               cvmx_dprintf("cvmx_helper_get_interface_num: "
+                            "Illegal IPD port number\n");
+
+       return -1;
+}
+
+/**
+ * Returns the interface index number for an IPD/PKO port
+ * number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface index number
+ */
+int cvmx_helper_get_interface_index_num(int ipd_port)
+{
+       if (ipd_port < 32)
+               return ipd_port & 15;
+       else if (ipd_port < 36)
+               return ipd_port & 3;
+       else if (ipd_port < 40)
+               return ipd_port & 3;
+       else
+               cvmx_dprintf("cvmx_helper_get_interface_index_num: "
+                            "Illegal IPD port number\n");
+
+       return -1;
+}
+
+/**
+ * Initialize the internal QLM JTAG logic to allow programming
+ * of the JTAG chain by the cvmx_helper_qlm_jtag_*() functions.
+ * These functions should only be used at the direction of Cavium
+ * Networks. Programming incorrect values into the JTAG chain
+ * can cause chip damage.
+ */
+void cvmx_helper_qlm_jtag_init(void)
+{
+       union cvmx_ciu_qlm_jtgc jtgc;
+       int clock_div = 0;
+       int divisor = cvmx_sysinfo_get()->cpu_clock_hz / (25 * 1000000);
+       divisor = (divisor - 1) >> 2;
+       /* Convert the divisor into a power of 2 shift */
+       CVMX_CLZ(clock_div, divisor);
+       clock_div = 32 - clock_div;
+
+       /*
+        * Clock divider for QLM JTAG operations.  eclk is divided by
+        * 2^(CLK_DIV + 2).
+        */
+       jtgc.u64 = 0;
+       jtgc.s.clk_div = clock_div;
+       jtgc.s.mux_sel = 0;
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX))
+               jtgc.s.bypass = 0x3;
+       else
+               jtgc.s.bypass = 0xf;
+       cvmx_write_csr(CVMX_CIU_QLM_JTGC, jtgc.u64);
+       cvmx_read_csr(CVMX_CIU_QLM_JTGC);
+}
+
+/**
+ * Write up to 32bits into the QLM jtag chain. Bits are shifted
+ * into the MSB and out the LSB, so you should shift in the low
+ * order bits followed by the high order bits. The JTAG chain is
+ * 4 * 268 bits long, or 1072.
+ *
+ * @qlm:    QLM to shift value into
+ * @bits:   Number of bits to shift in (1-32).
+ * @data:   Data to shift in. Bit 0 enters the chain first, followed by
+ *               bit 1, etc.
+ *
+ * Returns The low order bits of the JTAG chain that shifted out of the
+ *         circle.
+ */
+uint32_t cvmx_helper_qlm_jtag_shift(int qlm, int bits, uint32_t data)
+{
+       union cvmx_ciu_qlm_jtgd jtgd;
+       jtgd.u64 = 0;
+       jtgd.s.shift = 1;
+       jtgd.s.shft_cnt = bits - 1;
+       jtgd.s.shft_reg = data;
+       if (!OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X))
+               jtgd.s.select = 1 << qlm;
+       cvmx_write_csr(CVMX_CIU_QLM_JTGD, jtgd.u64);
+       do {
+               jtgd.u64 = cvmx_read_csr(CVMX_CIU_QLM_JTGD);
+       } while (jtgd.s.shift);
+       return jtgd.s.shft_reg >> (32 - bits);
+}
+
+/**
+ * Shift long sequences of zeros into the QLM JTAG chain. It is
+ * common to need to shift more than 32 bits of zeros into the
+ * chain. This function is a convience wrapper around
+ * cvmx_helper_qlm_jtag_shift() to shift more than 32 bits of
+ * zeros at a time.
+ *
+ * @qlm:    QLM to shift zeros into
+ * @bits:
+ */
+void cvmx_helper_qlm_jtag_shift_zeros(int qlm, int bits)
+{
+       while (bits > 0) {
+               int n = bits;
+               if (n > 32)
+                       n = 32;
+               cvmx_helper_qlm_jtag_shift(qlm, n, 0);
+               bits -= n;
+       }
+}
+
+/**
+ * Program the QLM JTAG chain into all lanes of the QLM. You must
+ * have already shifted in 268*4, or 1072 bits into the JTAG
+ * chain. Updating invalid values can possibly cause chip damage.
+ *
+ * @qlm:    QLM to program
+ */
+void cvmx_helper_qlm_jtag_update(int qlm)
+{
+       union cvmx_ciu_qlm_jtgd jtgd;
+
+       /* Update the new data */
+       jtgd.u64 = 0;
+       jtgd.s.update = 1;
+       if (!OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X))
+               jtgd.s.select = 1 << qlm;
+       cvmx_write_csr(CVMX_CIU_QLM_JTGD, jtgd.u64);
+       do {
+               jtgd.u64 = cvmx_read_csr(CVMX_CIU_QLM_JTGD);
+       } while (jtgd.s.update);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-pcie.c 
b/arch/mips/cavium-octeon/executive/cvmx-pcie.c
new file mode 100644
index 0000000..710f21f
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-pcie.c
@@ -0,0 +1,1053 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Interface to PCIe as a host(RC) or target(EP)
+ *
+ */
+#include <linux/delay.h>
+#include <linux/byteorder.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npei-defs.h>
+#include <asm/octeon/cvmx-pciercx-defs.h>
+#include <asm/octeon/cvmx-pescx-defs.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+#include <asm/octeon/cvmx-pcieep-defs.h>
+#include <asm/octeon/cvmx-helper-errata.h>
+#include <asm/octeon/cvmx-pcie.h>
+
+/**
+ * Return the Core virtual base address for PCIe IO access. IOs are
+ * read/written as an offset from this address.
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns 64bit Octeon IO base address for read/write
+ */
+uint64_t cvmx_pcie_get_io_base_address(int pcie_port)
+{
+       union cvmx_pcie_address pcie_addr;
+       pcie_addr.u64 = 0;
+       pcie_addr.io.upper = 0;
+       pcie_addr.io.io = 1;
+       pcie_addr.io.did = 3;
+       pcie_addr.io.subdid = 2;
+       pcie_addr.io.es = 1;
+       pcie_addr.io.port = pcie_port;
+       return pcie_addr.u64;
+}
+
+/**
+ * Size of the IO address region returned at address
+ * cvmx_pcie_get_io_base_address()
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns Size of the IO window
+ */
+uint64_t cvmx_pcie_get_io_size(int pcie_port)
+{
+       return 1ull << 32;
+}
+
+/**
+ * Return the Core virtual base address for PCIe MEM access. Memory is
+ * read/written as an offset from this address.
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns 64bit Octeon IO base address for read/write
+ */
+uint64_t cvmx_pcie_get_mem_base_address(int pcie_port)
+{
+       union cvmx_pcie_address pcie_addr;
+       pcie_addr.u64 = 0;
+       pcie_addr.mem.upper = 0;
+       pcie_addr.mem.io = 1;
+       pcie_addr.mem.did = 3;
+       pcie_addr.mem.subdid = 3 + pcie_port;
+       return pcie_addr.u64;
+}
+
+/**
+ * Size of the Mem address region returned at address
+ * cvmx_pcie_get_mem_base_address()
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns Size of the Mem window
+ */
+uint64_t cvmx_pcie_get_mem_size(int pcie_port)
+{
+       return 1ull << 36;
+}
+
+/**
+ * Initialize the RC config space CSRs
+ *
+ * @pcie_port: PCIe port to initialize
+ */
+static void __cvmx_pcie_rc_initialize_config_space(int pcie_port)
+{
+       union cvmx_pciercx_cfg030 pciercx_cfg030;
+       union cvmx_npei_ctl_status2 npei_ctl_status2;
+       union cvmx_pciercx_cfg070 pciercx_cfg070;
+       union cvmx_pciercx_cfg001 pciercx_cfg001;
+       union cvmx_pciercx_cfg032 pciercx_cfg032;
+       union cvmx_pciercx_cfg006 pciercx_cfg006;
+       union cvmx_pciercx_cfg008 pciercx_cfg008;
+       union cvmx_pciercx_cfg009 pciercx_cfg009;
+       union cvmx_pciercx_cfg010 pciercx_cfg010;
+       union cvmx_pciercx_cfg011 pciercx_cfg011;
+       union cvmx_pciercx_cfg035 pciercx_cfg035;
+       union cvmx_pciercx_cfg075 pciercx_cfg075;
+       union cvmx_pciercx_cfg034 pciercx_cfg034;
+
+       /* Max Payload Size (PCIE*_CFG030[MPS]) */
+       /* Max Read Request Size (PCIE*_CFG030[MRRS]) */
+       /* Relaxed-order, no-snoop enables (PCIE*_CFG030[RO_EN,NS_EN] */
+       /* Error Message Enables (PCIE*_CFG030[CE_EN,NFE_EN,FE_EN,UR_EN]) */
+       pciercx_cfg030.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG030(pcie_port));
+       /*
+        * Max payload size = 128 bytes for best Octeon DMA
+        * performance.
+        */
+       pciercx_cfg030.s.mps = 0;
+       /*
+        * Max read request size = 128 bytes for best Octeon DMA
+        * performance.
+        */
+       pciercx_cfg030.s.mrrs = 0;
+       /* Enable relaxed ordering. */
+       pciercx_cfg030.s.ro_en = 1;
+       /* Enable no snoop. */
+       pciercx_cfg030.s.ns_en = 1;
+       /* Correctable error reporting enable. */
+       pciercx_cfg030.s.ce_en = 1;
+       /* Non-fatal error reporting enable. */
+       pciercx_cfg030.s.nfe_en = 1;
+       /* Fatal error reporting enable. */
+       pciercx_cfg030.s.fe_en = 1;
+       /* Unsupported request reporting enable. */
+       pciercx_cfg030.s.ur_en = 1;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG030(pcie_port),
+                            pciercx_cfg030.u32);
+
+       /*
+        * Max Payload Size (NPEI_CTL_STATUS2[MPS]) must match
+        * PCIE*_CFG030[MPS]
+        *
+        * Max Read Request Size (NPEI_CTL_STATUS2[MRRS]) must not
+        * exceed PCIE*_CFG030[MRRS].
+        */
+       npei_ctl_status2.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS2);
+       /* Max payload size = 128 bytes for best Octeon DMA performance */
+       npei_ctl_status2.s.mps = 0;
+       /* Max read request size = 128 bytes for best Octeon DMA performance */
+       npei_ctl_status2.s.mrrs = 0;
+       cvmx_write_csr(CVMX_PEXP_NPEI_CTL_STATUS2, npei_ctl_status2.u64);
+
+       /* ECRC Generation (PCIE*_CFG070[GE,CE]) */
+       pciercx_cfg070.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG070(pcie_port));
+       pciercx_cfg070.s.ge = 1;        /* ECRC generation enable. */
+       pciercx_cfg070.s.ce = 1;        /* ECRC check enable. */
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG070(pcie_port),
+                            pciercx_cfg070.u32);
+
+       /*
+        * Access Enables (PCIE*_CFG001[MSAE,ME]) ME and MSAE should
+        * always be set.
+        *
+        * Interrupt Disable (PCIE*_CFG001[I_DIS]) System Error
+        * Message Enable (PCIE*_CFG001[SEE])
+        */
+       pciercx_cfg001.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG001(pcie_port));
+       pciercx_cfg001.s.msae = 1;      /* Memory space enable. */
+       pciercx_cfg001.s.me = 1;        /* Bus master enable. */
+       pciercx_cfg001.s.i_dis = 1;     /* INTx assertion disable. */
+       pciercx_cfg001.s.see = 1;       /* SERR# enable */
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG001(pcie_port),
+                       pciercx_cfg001.u32);
+
+       /* Advanced Error Recovery Message Enables */
+       /* (PCIE*_CFG066,PCIE*_CFG067,PCIE*_CFG069) */
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG066(pcie_port), 0);
+       /* Use CVMX_PCIERCX_CFG067 hardware default */
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG069(pcie_port), 0);
+
+       /* Active State Power Management (PCIE*_CFG032[ASLPC]) */
+       pciercx_cfg032.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+       pciercx_cfg032.s.aslpc = 0;     /* Active state Link PM control. */
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG032(pcie_port),
+                            pciercx_cfg032.u32);
+
+       /* Entrance Latencies (PCIE*_CFG451[L0EL,L1EL]) */
+
+       /*
+        * Link Width Mode (PCIERCn_CFG452[LME]) - Set during
+        * cvmx_pcie_rc_initialize_link()
+        *
+        * Primary Bus Number (PCIERCn_CFG006[PBNUM])
+        *
+        * We set the primary bus number to 1 so IDT bridges are
+        * happy. They don't like zero.
+        */
+       pciercx_cfg006.u32 = 0;
+       pciercx_cfg006.s.pbnum = 1;
+       pciercx_cfg006.s.sbnum = 1;
+       pciercx_cfg006.s.subbnum = 1;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG006(pcie_port),
+                            pciercx_cfg006.u32);
+
+       /*
+        * Memory-mapped I/O BAR (PCIERCn_CFG008)
+        * Most applications should disable the memory-mapped I/O BAR by
+        * setting PCIERCn_CFG008[ML_ADDR] < PCIERCn_CFG008[MB_ADDR]
+        */
+       pciercx_cfg008.u32 = 0;
+       pciercx_cfg008.s.mb_addr = 0x100;
+       pciercx_cfg008.s.ml_addr = 0;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG008(pcie_port),
+                            pciercx_cfg008.u32);
+
+       /*
+        * Prefetchable BAR (PCIERCn_CFG009,PCIERCn_CFG010,PCIERCn_CFG011)
+        * Most applications should disable the prefetchable BAR by setting
+        * PCIERCn_CFG011[UMEM_LIMIT],PCIERCn_CFG009[LMEM_LIMIT] <
+        * PCIERCn_CFG010[UMEM_BASE],PCIERCn_CFG009[LMEM_BASE]
+        */
+       pciercx_cfg009.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG009(pcie_port));
+       pciercx_cfg010.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG010(pcie_port));
+       pciercx_cfg011.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG011(pcie_port));
+       pciercx_cfg009.s.lmem_base = 0x100;
+       pciercx_cfg009.s.lmem_limit = 0;
+       pciercx_cfg010.s.umem_base = 0x100;
+       pciercx_cfg011.s.umem_limit = 0;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG009(pcie_port),
+                            pciercx_cfg009.u32);
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG010(pcie_port),
+                            pciercx_cfg010.u32);
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG011(pcie_port),
+                            pciercx_cfg011.u32);
+
+       /*
+        * System Error Interrupt Enables (PCIERCn_CFG035[SECEE,SEFEE,SENFEE])
+        * PME Interrupt Enables (PCIERCn_CFG035[PMEIE])
+        */
+       pciercx_cfg035.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG035(pcie_port));
+       /* System error on correctable error enable. */
+       pciercx_cfg035.s.secee = 1;
+       /* System error on fatal error enable. */
+       pciercx_cfg035.s.sefee = 1;
+       /* System error on non-fatal error enable. */
+       pciercx_cfg035.s.senfee = 1;
+       /* PME interrupt enable. */
+       pciercx_cfg035.s.pmeie = 1;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG035(pcie_port),
+                            pciercx_cfg035.u32);
+
+       /*
+        * Advanced Error Recovery Interrupt Enables
+        * (PCIERCn_CFG075[CERE,NFERE,FERE])
+        */
+       pciercx_cfg075.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG075(pcie_port));
+       /* Correctable error reporting enable. */
+       pciercx_cfg075.s.cere = 1;
+       /* Non-fatal error reporting enable. */
+       pciercx_cfg075.s.nfere = 1;
+       /* Fatal error reporting enable. */
+       pciercx_cfg075.s.fere = 1;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG075(pcie_port),
+                            pciercx_cfg075.u32);
+
+       /* HP Interrupt Enables (PCIERCn_CFG034[HPINT_EN],
+        * PCIERCn_CFG034[DLLS_EN,CCINT_EN])
+        */
+       pciercx_cfg034.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG034(pcie_port));
+       /* Hot-plug interrupt enable. */
+       pciercx_cfg034.s.hpint_en = 1;
+       /* Data Link Layer state changed enable */
+       pciercx_cfg034.s.dlls_en = 1;
+       /* Command completed interrupt enable. */
+       pciercx_cfg034.s.ccint_en = 1;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG034(pcie_port),
+                            pciercx_cfg034.u32);
+}
+
+/**
+ * Initialize a host mode PCIe link. This function takes a PCIe
+ * port from reset to a link up state. Software can then begin
+ * configuring the rest of the link.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success
+ */
+static int __cvmx_pcie_rc_initialize_link(int pcie_port)
+{
+       uint64_t start_cycle;
+       union cvmx_pescx_ctl_status pescx_ctl_status;
+       union cvmx_pciercx_cfg452 pciercx_cfg452;
+       union cvmx_pciercx_cfg032 pciercx_cfg032;
+       union cvmx_pciercx_cfg448 pciercx_cfg448;
+
+       /* Set the lane width */
+       pciercx_cfg452.u32 =
+           cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG452(pcie_port));
+       pescx_ctl_status.u64 = cvmx_read_csr(CVMX_PESCX_CTL_STATUS(pcie_port));
+       if (pescx_ctl_status.s.qlm_cfg == 0) {
+               /* We're in 8 lane (56XX) or 4 lane (54XX) mode */
+               pciercx_cfg452.s.lme = 0xf;
+       } else {
+               /* We're in 4 lane (56XX) or 2 lane (52XX) mode */
+               pciercx_cfg452.s.lme = 0x7;
+       }
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG452(pcie_port),
+                            pciercx_cfg452.u32);
+
+       /*
+        * CN52XX pass 1.x has an errata where length mismatches on UR
+        * responses can cause bus errors on 64bit memory
+        * reads. Turning off length error checking fixes this.
+        */
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+               union cvmx_pciercx_cfg455 pciercx_cfg455;
+               pciercx_cfg455.u32 =
+                   cvmx_pcie_cfgx_read(pcie_port,
+                                       CVMX_PCIERCX_CFG455(pcie_port));
+               pciercx_cfg455.s.m_cpl_len_err = 1;
+               cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG455(pcie_port),
+                                    pciercx_cfg455.u32);
+       }
+
+       /* Lane swap needs to be manually enabled for CN52XX */
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX) && (pcie_port == 1)) {
+               pescx_ctl_status.s.lane_swp = 1;
+               cvmx_write_csr(CVMX_PESCX_CTL_STATUS(pcie_port),
+                              pescx_ctl_status.u64);
+       }
+
+       /* Bring up the link */
+       pescx_ctl_status.u64 = cvmx_read_csr(CVMX_PESCX_CTL_STATUS(pcie_port));
+       pescx_ctl_status.s.lnk_enb = 1;
+       cvmx_write_csr(CVMX_PESCX_CTL_STATUS(pcie_port), pescx_ctl_status.u64);
+
+       /*
+        * CN52XX pass 1.0: Due to a bug in 2nd order CDR, it needs to
+        * be disabled.
+        */
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_0))
+               __cvmx_helper_errata_qlm_disable_2nd_order_cdr(0);
+
+       /* Wait for the link to come up */
+       cvmx_dprintf("PCIe: Waiting for port %d link\n", pcie_port);
+       start_cycle = cvmx_get_cycle();
+       do {
+               if (cvmx_get_cycle() - start_cycle >
+                   2 * cvmx_sysinfo_get()->cpu_clock_hz) {
+                       cvmx_dprintf("PCIe: Port %d link timeout\n",
+                                    pcie_port);
+                       return -1;
+               }
+               cvmx_wait(10000);
+               pciercx_cfg032.u32 =
+                   cvmx_pcie_cfgx_read(pcie_port,
+                                       CVMX_PCIERCX_CFG032(pcie_port));
+       } while (pciercx_cfg032.s.dlla == 0);
+
+       /* Display the link status */
+       cvmx_dprintf("PCIe: Port %d link active, %d lanes\n", pcie_port,
+                    pciercx_cfg032.s.nlw);
+
+       /*
+        * Update the Replay Time Limit. Empirically, some PCIe
+        * devices take a little longer to respond than expected under
+        * load. As a workaround for this we configure the Replay Time
+        * Limit to the value expected for a 512 byte MPS instead of
+        * our actual 256 byte MPS. The numbers below are directly
+        * from the PCIe spec table 3-4.
+        */
+       pciercx_cfg448.u32 =
+           cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG448(pcie_port));
+       switch (pciercx_cfg032.s.nlw) {
+       case 1:         /* 1 lane */
+               pciercx_cfg448.s.rtl = 1677;
+               break;
+       case 2:         /* 2 lanes */
+               pciercx_cfg448.s.rtl = 867;
+               break;
+       case 4:         /* 4 lanes */
+               pciercx_cfg448.s.rtl = 462;
+               break;
+       case 8:         /* 8 lanes */
+               pciercx_cfg448.s.rtl = 258;
+               break;
+       }
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG448(pcie_port),
+                            pciercx_cfg448.u32);
+
+       return 0;
+}
+
+/**
+ * Initialize a PCIe port for use in host(RC) mode. It doesn't
+ * enumerate the bus.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success
+ */
+int cvmx_pcie_rc_initialize(int pcie_port)
+{
+       int i;
+       union cvmx_ciu_soft_prst ciu_soft_prst;
+       union cvmx_pescx_bist_status pescx_bist_status;
+       union cvmx_pescx_bist_status2 pescx_bist_status2;
+       union cvmx_npei_ctl_status npei_ctl_status;
+       union cvmx_npei_mem_access_ctl npei_mem_access_ctl;
+       union cvmx_npei_mem_access_subidx mem_access_subid;
+       union cvmx_npei_dbg_data npei_dbg_data;
+       union cvmx_pescx_ctl_status2 pescx_ctl_status2;
+
+       /*
+        * Make sure we aren't trying to setup a target mode interface
+        * in host mode.
+        */
+       npei_ctl_status.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS);
+       if ((pcie_port == 0) && !npei_ctl_status.s.host_mode) {
+               cvmx_dprintf("PCIe: ERROR: cvmx_pcie_rc_initialize() called "
+                            "on port0, but port0 is not in host mode\n");
+               return -1;
+       }
+
+       /*
+        * Make sure a CN52XX isn't trying to bring up port 1 when it
+        * is disabled.
+        */
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+               npei_dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+               if ((pcie_port == 1) && npei_dbg_data.cn52xx.qlm0_link_width) {
+                       cvmx_dprintf("PCIe: ERROR: cvmx_pcie_rc_initialize() "
+                                    "called on port1, but port1 is 
disabled\n");
+                       return -1;
+               }
+       }
+
+       /*
+        * PCIe switch arbitration mode. '0' == fixed priority NPEI,
+        * PCIe0, then PCIe1. '1' == round robin.
+        */
+       npei_ctl_status.s.arb = 1;
+       /* Allow up to 0x20 config retries */
+       npei_ctl_status.s.cfg_rtry = 0x20;
+       /*
+        * CN52XX pass1.x has an errata where P0_NTAGS and P1_NTAGS
+        * don't reset.
+        */
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+               npei_ctl_status.s.p0_ntags = 0x20;
+               npei_ctl_status.s.p1_ntags = 0x20;
+       }
+       cvmx_write_csr(CVMX_PEXP_NPEI_CTL_STATUS, npei_ctl_status.u64);
+
+       /* Bring the PCIe out of reset */
+       if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_EBH5200) {
+               /*
+                * The EBH5200 board swapped the PCIe reset lines on
+                * the board. As a workaround for this bug, we bring
+                * both PCIe ports out of reset at the same time
+                * instead of on separate calls. So for port 0, we
+                * bring both out of reset and do nothing on port 1.
+                */
+               if (pcie_port == 0) {
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+                       /*
+                        * After a chip reset the PCIe will also be in
+                        * reset. If it isn't, most likely someone is
+                        * trying to init it again without a proper
+                        * PCIe reset.
+                        */
+                       if (ciu_soft_prst.s.soft_prst == 0) {
+                               /* Reset the ports */
+                               ciu_soft_prst.s.soft_prst = 1;
+                               cvmx_write_csr(CVMX_CIU_SOFT_PRST,
+                                              ciu_soft_prst.u64);
+                               ciu_soft_prst.u64 =
+                                   cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+                               ciu_soft_prst.s.soft_prst = 1;
+                               cvmx_write_csr(CVMX_CIU_SOFT_PRST1,
+                                              ciu_soft_prst.u64);
+                               /* Wait until pcie resets the ports. */
+                               udelay(2000);
+                       }
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+                       ciu_soft_prst.s.soft_prst = 0;
+                       cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+                       ciu_soft_prst.s.soft_prst = 0;
+                       cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+               }
+       } else {
+               /*
+                * The normal case: The PCIe ports are completely
+                * separate and can be brought out of reset
+                * independently.
+                */
+               if (pcie_port)
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+               else
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+               /*
+                * After a chip reset the PCIe will also be in
+                * reset. If it isn't, most likely someone is trying
+                * to init it again without a proper PCIe reset.
+                */
+               if (ciu_soft_prst.s.soft_prst == 0) {
+                       /* Reset the port */
+                       ciu_soft_prst.s.soft_prst = 1;
+                       if (pcie_port)
+                               cvmx_write_csr(CVMX_CIU_SOFT_PRST1,
+                                              ciu_soft_prst.u64);
+                       else
+                               cvmx_write_csr(CVMX_CIU_SOFT_PRST,
+                                              ciu_soft_prst.u64);
+                       /* Wait until pcie resets the ports. */
+                       udelay(2000);
+               }
+               if (pcie_port) {
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+                       ciu_soft_prst.s.soft_prst = 0;
+                       cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+               } else {
+                       ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+                       ciu_soft_prst.s.soft_prst = 0;
+                       cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+               }
+       }
+
+       /*
+        * Wait for PCIe reset to complete. Due to errata PCIE-700, we
+        * don't poll PESCX_CTL_STATUS2[PCIERST], but simply wait a
+        * fixed number of cycles.
+        */
+       cvmx_wait(400000);
+
+       /* PESCX_BIST_STATUS2[PCLK_RUN] was missing on pass 1 of CN56XX and
+          CN52XX, so we only probe it on newer chips */
+       if (!OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X)
+           && !OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+               /* Clear PCLK_RUN so we can check if the clock is running */
+               pescx_ctl_status2.u64 =
+                   cvmx_read_csr(CVMX_PESCX_CTL_STATUS2(pcie_port));
+               pescx_ctl_status2.s.pclk_run = 1;
+               cvmx_write_csr(CVMX_PESCX_CTL_STATUS2(pcie_port),
+                              pescx_ctl_status2.u64);
+               /*
+                * Now that we cleared PCLK_RUN, wait for it to be set
+                * again telling us the clock is running.
+                */
+               if (CVMX_WAIT_FOR_FIELD64(CVMX_PESCX_CTL_STATUS2(pcie_port),
+                                         union cvmx_pescx_ctl_status2,
+                                         pclk_run, ==, 1, 10000)) {
+                       cvmx_dprintf("PCIe: Port %d isn't clocked, skipping.\n",
+                                    pcie_port);
+                       return -1;
+               }
+       }
+
+       /*
+        * Check and make sure PCIe came out of reset. If it doesn't
+        * the board probably hasn't wired the clocks up and the
+        * interface should be skipped.
+        */
+       pescx_ctl_status2.u64 =
+           cvmx_read_csr(CVMX_PESCX_CTL_STATUS2(pcie_port));
+       if (pescx_ctl_status2.s.pcierst) {
+               cvmx_dprintf("PCIe: Port %d stuck in reset, skipping.\n",
+                            pcie_port);
+               return -1;
+       }
+
+       /*
+        * Check BIST2 status. If any bits are set skip this interface. This
+        * is an attempt to catch PCIE-813 on pass 1 parts.
+        */
+       pescx_bist_status2.u64 =
+           cvmx_read_csr(CVMX_PESCX_BIST_STATUS2(pcie_port));
+       if (pescx_bist_status2.u64) {
+               cvmx_dprintf("PCIe: Port %d BIST2 failed. Most likely this "
+                            "port isn't hooked up, skipping.\n",
+                            pcie_port);
+               return -1;
+       }
+
+       /* Check BIST status */
+       pescx_bist_status.u64 =
+           cvmx_read_csr(CVMX_PESCX_BIST_STATUS(pcie_port));
+       if (pescx_bist_status.u64)
+               cvmx_dprintf("PCIe: BIST FAILED for port %d (0x%016llx)\n",
+                            pcie_port, CAST64(pescx_bist_status.u64));
+
+       /* Initialize the config space CSRs */
+       __cvmx_pcie_rc_initialize_config_space(pcie_port);
+
+       /* Bring the link up */
+       if (__cvmx_pcie_rc_initialize_link(pcie_port)) {
+               cvmx_dprintf
+                   ("PCIe: ERROR: cvmx_pcie_rc_initialize_link() failed\n");
+               return -1;
+       }
+
+       /* Store merge control (NPEI_MEM_ACCESS_CTL[TIMER,MAX_WORD]) */
+       npei_mem_access_ctl.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_MEM_ACCESS_CTL);
+       /* Allow 16 words to combine */
+       npei_mem_access_ctl.s.max_word = 0;
+       /* Wait up to 127 cycles for more data */
+       npei_mem_access_ctl.s.timer = 127;
+       cvmx_write_csr(CVMX_PEXP_NPEI_MEM_ACCESS_CTL, npei_mem_access_ctl.u64);
+
+       /* Setup Mem access SubDIDs */
+       mem_access_subid.u64 = 0;
+       /* Port the request is sent to. */
+       mem_access_subid.s.port = pcie_port;
+       /* Due to an errata on pass 1 chips, no merging is allowed. */
+       mem_access_subid.s.nmerge = 1;
+       /* Endian-swap for Reads. */
+       mem_access_subid.s.esr = 1;
+       /* Endian-swap for Writes. */
+       mem_access_subid.s.esw = 1;
+       /* No Snoop for Reads. */
+       mem_access_subid.s.nsr = 1;
+       /* No Snoop for Writes. */
+       mem_access_subid.s.nsw = 1;
+       /* Disable Relaxed Ordering for Reads. */
+       mem_access_subid.s.ror = 0;
+       /* Disable Relaxed Ordering for Writes. */
+       mem_access_subid.s.row = 0;
+       /* PCIe Adddress Bits <63:34>. */
+       mem_access_subid.s.ba = 0;
+
+       /*
+        * Setup mem access 12-15 for port 0, 16-19 for port 1,
+        * supplying 36 bits of address space.
+        */
+       for (i = 12 + pcie_port * 4; i < 16 + pcie_port * 4; i++) {
+               cvmx_write_csr(CVMX_PEXP_NPEI_MEM_ACCESS_SUBIDX(i),
+                              mem_access_subid.u64);
+               /* Set each SUBID to extend the addressable range */
+               mem_access_subid.s.ba += 1;
+       }
+
+       /*
+        * Disable the peer to peer forwarding register. This must be
+        * setup by the OS after it enumerates the bus and assigns
+        * addresses to the PCIe busses.
+        */
+       for (i = 0; i < 4; i++) {
+               cvmx_write_csr(CVMX_PESCX_P2P_BARX_START(i, pcie_port), -1);
+               cvmx_write_csr(CVMX_PESCX_P2P_BARX_END(i, pcie_port), -1);
+       }
+
+       /* Set Octeon's BAR0 to decode 0-16KB. It overlaps with Bar2 */
+       cvmx_write_csr(CVMX_PESCX_P2N_BAR0_START(pcie_port), 0);
+
+       /*
+        * Disable Octeon's BAR1. It isn't needed in RC mode since
+        * BAR2 maps all of memory. BAR2 also maps 256MB-512MB into
+        * the 2nd 256MB of memory.
+        */
+       cvmx_write_csr(CVMX_PESCX_P2N_BAR1_START(pcie_port), -1);
+
+       /*
+        * Set Octeon's BAR2 to decode 0-2^39. Bar0 and Bar1 take
+        * precedence where they overlap. It also overlaps with the
+        * device addresses, so make sure the peer to peer forwarding
+        * is set right.
+        */
+       cvmx_write_csr(CVMX_PESCX_P2N_BAR2_START(pcie_port), 0);
+
+       /*
+        * Setup BAR2 attributes
+        *
+        * Relaxed Ordering (NPEI_CTL_PORTn[PTLP_RO,CTLP_RO, WAIT_COM])
+        * - PTLP_RO,CTLP_RO should normally be set (except for debug).
+        * - WAIT_COM=0 will likely work for all applications.
+        *
+        * Load completion relaxed ordering (NPEI_CTL_PORTn[WAITL_COM]).
+        */
+       if (pcie_port) {
+               union cvmx_npei_ctl_port1 npei_ctl_port;
+               npei_ctl_port.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_PORT1);
+               npei_ctl_port.s.bar2_enb = 1;
+               npei_ctl_port.s.bar2_esx = 1;
+               npei_ctl_port.s.bar2_cax = 0;
+               npei_ctl_port.s.ptlp_ro = 1;
+               npei_ctl_port.s.ctlp_ro = 1;
+               npei_ctl_port.s.wait_com = 0;
+               npei_ctl_port.s.waitl_com = 0;
+               cvmx_write_csr(CVMX_PEXP_NPEI_CTL_PORT1, npei_ctl_port.u64);
+       } else {
+               union cvmx_npei_ctl_port0 npei_ctl_port;
+               npei_ctl_port.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_PORT0);
+               npei_ctl_port.s.bar2_enb = 1;
+               npei_ctl_port.s.bar2_esx = 1;
+               npei_ctl_port.s.bar2_cax = 0;
+               npei_ctl_port.s.ptlp_ro = 1;
+               npei_ctl_port.s.ctlp_ro = 1;
+               npei_ctl_port.s.wait_com = 0;
+               npei_ctl_port.s.waitl_com = 0;
+               cvmx_write_csr(CVMX_PEXP_NPEI_CTL_PORT0, npei_ctl_port.u64);
+       }
+       return 0;
+}
+
+/**
+ * Shutdown a PCIe port and put it in reset
+ *
+ * @pcie_port: PCIe port to shutdown
+ *
+ * Returns Zero on success
+ */
+int cvmx_pcie_rc_shutdown(int pcie_port)
+{
+       /* Wait for all pending operations to complete */
+       if (CVMX_WAIT_FOR_FIELD64(CVMX_PESCX_CPL_LUT_VALID(pcie_port),
+                                 union cvmx_pescx_cpl_lut_valid,
+                                 tag, ==, 0, 2000))
+               cvmx_dprintf("PCIe: Port %d shutdown timeout\n", pcie_port);
+
+       /* Force reset */
+       if (pcie_port) {
+               union cvmx_ciu_soft_prst ciu_soft_prst;
+               ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+               ciu_soft_prst.s.soft_prst = 1;
+               cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+       } else {
+               union cvmx_ciu_soft_prst ciu_soft_prst;
+               ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+               ciu_soft_prst.s.soft_prst = 1;
+               cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+       }
+       return 0;
+}
+
+/**
+ * Build a PCIe config space request address for a device
+ *
+ * @pcie_port: PCIe port to access
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns 64bit Octeon IO address
+ */
+static inline uint64_t __cvmx_pcie_build_config_addr(int pcie_port, int bus,
+                                                    int dev, int fn, int reg)
+{
+       union cvmx_pcie_address pcie_addr;
+       union cvmx_pciercx_cfg006 pciercx_cfg006;
+
+       pciercx_cfg006.u32 =
+           cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG006(pcie_port));
+       if ((bus <= pciercx_cfg006.s.pbnum) && (dev != 0))
+               return 0;
+
+       pcie_addr.u64 = 0;
+       pcie_addr.config.upper = 2;
+       pcie_addr.config.io = 1;
+       pcie_addr.config.did = 3;
+       pcie_addr.config.subdid = 1;
+       pcie_addr.config.es = 1;
+       pcie_addr.config.port = pcie_port;
+       pcie_addr.config.ty = (bus > pciercx_cfg006.s.pbnum);
+       pcie_addr.config.bus = bus;
+       pcie_addr.config.dev = dev;
+       pcie_addr.config.func = fn;
+       pcie_addr.config.reg = reg;
+       return pcie_addr.u64;
+}
+
+/**
+ * Read 8bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+uint8_t cvmx_pcie_config_read8(int pcie_port, int bus, int dev,
+                              int fn, int reg)
+{
+       uint64_t address =
+           __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+       if (address)
+               return cvmx_read64_uint8(address);
+       else
+               return 0xff;
+}
+
+/**
+ * Read 16bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+uint16_t cvmx_pcie_config_read16(int pcie_port, int bus, int dev, int fn,
+                                int reg)
+{
+       uint64_t address =
+           __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+       if (address)
+               return le16_to_cpu(cvmx_read64_uint16(address));
+       else
+               return 0xffff;
+}
+
+/**
+ * Read 32bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+uint32_t cvmx_pcie_config_read32(int pcie_port, int bus, int dev, int fn,
+                                int reg)
+{
+       uint64_t address =
+           __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+       if (address)
+               return le32_to_cpu(cvmx_read64_uint32(address));
+       else
+               return 0xffffffff;
+}
+
+/**
+ * Write 8bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+void cvmx_pcie_config_write8(int pcie_port, int bus, int dev, int fn,
+                            int reg, uint8_t val)
+{
+       uint64_t address =
+           __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+       if (address)
+               cvmx_write64_uint8(address, val);
+}
+
+/**
+ * Write 16bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+void cvmx_pcie_config_write16(int pcie_port, int bus, int dev, int fn,
+                             int reg, uint16_t val)
+{
+       uint64_t address =
+           __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+       if (address)
+               cvmx_write64_uint16(address, cpu_to_le16(val));
+}
+
+/**
+ * Write 32bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+void cvmx_pcie_config_write32(int pcie_port, int bus, int dev, int fn,
+                             int reg, uint32_t val)
+{
+       uint64_t address =
+           __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+       if (address)
+               cvmx_write64_uint32(address, cpu_to_le32(val));
+}
+
+/**
+ * Read a PCIe config space register indirectly. This is used for
+ * registers of the form PCIEEP_CFG??? and PCIERC?_CFG???.
+ *
+ * @pcie_port:  PCIe port to read from
+ * @cfg_offset: Address to read
+ *
+ * Returns Value read
+ */
+uint32_t cvmx_pcie_cfgx_read(int pcie_port, uint32_t cfg_offset)
+{
+       union cvmx_pescx_cfg_rd pescx_cfg_rd;
+       pescx_cfg_rd.u64 = 0;
+       pescx_cfg_rd.s.addr = cfg_offset;
+       cvmx_write_csr(CVMX_PESCX_CFG_RD(pcie_port), pescx_cfg_rd.u64);
+       pescx_cfg_rd.u64 = cvmx_read_csr(CVMX_PESCX_CFG_RD(pcie_port));
+       return pescx_cfg_rd.s.data;
+}
+
+/**
+ * Write a PCIe config space register indirectly. This is used for
+ * registers of the form PCIEEP_CFG??? and PCIERC?_CFG???.
+ *
+ * @pcie_port:  PCIe port to write to
+ * @cfg_offset: Address to write
+ * @val:        Value to write
+ */
+void cvmx_pcie_cfgx_write(int pcie_port, uint32_t cfg_offset, uint32_t val)
+{
+       union cvmx_pescx_cfg_wr pescx_cfg_wr;
+       pescx_cfg_wr.u64 = 0;
+       pescx_cfg_wr.s.addr = cfg_offset;
+       pescx_cfg_wr.s.data = val;
+       cvmx_write_csr(CVMX_PESCX_CFG_WR(pcie_port), pescx_cfg_wr.u64);
+}
+
+/**
+ * Initialize a PCIe port for use in target(EP) mode.
+ *
+ * Returns Zero on success
+ */
+int cvmx_pcie_ep_initialize(void)
+{
+       int pcie_port = 0;
+       union cvmx_npei_ctl_status npei_ctl_status;
+       union cvmx_pciercx_cfg030 pciercx_cfg030;
+       union cvmx_npei_ctl_status2 npei_ctl_status2;
+       union cvmx_npei_mem_access_subidx mem_access_subid;
+
+       npei_ctl_status.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS);
+       if (npei_ctl_status.s.host_mode)
+               return -1;
+
+       /* Enable bus master and memory */
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIEEP_CFG001, 0x6);
+
+       /*
+        * Max Payload Size (PCIE*_CFG030[MPS])
+        * Max Read Request Size (PCIE*_CFG030[MRRS])
+        * Relaxed-order, no-snoop enables (PCIE*_CFG030[RO_EN,NS_EN]
+        * Error Message Enables (PCIE*_CFG030[CE_EN,NFE_EN,FE_EN,UR_EN])
+        */
+       pciercx_cfg030.u32 =
+               cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG030(pcie_port));
+       /* Max payload size = 128 bytes (Limit of most PCs) */
+       pciercx_cfg030.s.mps = 0;
+       /*
+        * Max read request size = 128 bytes for best Octeon DMA
+        * performance.
+        */
+       pciercx_cfg030.s.mrrs = 0;
+       /* Enable relaxed ordering. */
+       pciercx_cfg030.s.ro_en = 1;
+       /* Enable no snoop. */
+       pciercx_cfg030.s.ns_en = 1;
+       /* Correctable error reporting enable. */
+       pciercx_cfg030.s.ce_en = 1;
+       /* Non-fatal error reporting enable. */
+       pciercx_cfg030.s.nfe_en = 1;
+       /* Fatal error reporting enable. */
+       pciercx_cfg030.s.fe_en = 1;
+       /* Unsupported request reporting enable. */
+       pciercx_cfg030.s.ur_en = 1;
+       cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG030(pcie_port),
+                            pciercx_cfg030.u32);
+
+       /*
+        * Max Payload Size (NPEI_CTL_STATUS2[MPS]) must match
+        * PCIE*_CFG030[MPS]
+        *
+        * Max Read Request Size (NPEI_CTL_STATUS2[MRRS]) must not
+        * exceed PCIE*_CFG030[MRRS]
+        */
+       npei_ctl_status2.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS2);
+       /* Max payload size = 128 bytes (Limit of most PCs) */
+       npei_ctl_status2.s.mps = 0;
+       /* Max read request size = 128 bytes for best Octeon DMA performance */
+       npei_ctl_status2.s.mrrs = 0;
+       cvmx_write_csr(CVMX_PEXP_NPEI_CTL_STATUS2, npei_ctl_status2.u64);
+
+       /* Setup Mem access SubDID 12 to access Host memory */
+       mem_access_subid.u64 = 0;
+       /* Port the request is sent to. */
+       mem_access_subid.s.port = pcie_port;
+       /* Merging is allowed in this window. */
+       mem_access_subid.s.nmerge = 1;
+       /* Endian-swap for Reads. */
+       mem_access_subid.s.esr = 0;
+       /* Endian-swap for Writes. */
+       mem_access_subid.s.esw = 0;
+       /* No Snoop for Reads. */
+       mem_access_subid.s.nsr = 1;
+       /* No Snoop for Writes. */
+       mem_access_subid.s.nsw = 1;
+       /* Disable Relaxed Ordering for Reads. */
+       mem_access_subid.s.ror = 0;
+       /* Disable Relaxed Ordering for Writes. */
+       mem_access_subid.s.row = 0;
+       /* PCIe Adddress Bits <63:34>. */
+       mem_access_subid.s.ba = 0;
+       cvmx_write_csr(CVMX_PEXP_NPEI_MEM_ACCESS_SUBIDX(12),
+                      mem_access_subid.u64);
+       return 0;
+}
diff --git a/arch/mips/cavium-octeon/msi.c b/arch/mips/cavium-octeon/msi.c
new file mode 100644
index 0000000..964b03b
--- /dev/null
+++ b/arch/mips/cavium-octeon/msi.c
@@ -0,0 +1,288 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2007 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/msi.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-pci-defs.h>
+#include <asm/octeon/cvmx-npei-defs.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+
+#include "pci-common.h"
+
+/*
+ * Each bit in msi_free_irq_bitmask represents a MSI interrupt that is
+ * in use.
+ */
+static uint64_t msi_free_irq_bitmask;
+
+/*
+ * Each bit in msi_multiple_irq_bitmask tells that the device using
+ * this bit in msi_free_irq_bitmask is also using the next bit. This
+ * is used so we can disable all of the MSI interrupts when a device
+ * uses multiple.
+ */
+static uint64_t msi_multiple_irq_bitmask;
+
+/*
+ * This lock controls updates to msi_free_irq_bitmask and
+ * msi_multiple_irq_bitmask.
+ */
+static DEFINE_SPINLOCK(msi_free_irq_bitmask_lock);
+
+
+/**
+ * Called when a driver request MSI interrupts instead of the
+ * legacy INT A-D. This routine will allocate multiple interrupts
+ * for MSI devices that support them. A device can override this by
+ * programming the MSI control bits [6:4] before calling
+ * pci_enable_msi().
+ *
+ * @param dev    Device requesting MSI interrupts
+ * @param desc   MSI descriptor
+ *
+ * Returns 0 on success.
+ */
+int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc)
+{
+       struct msi_msg msg;
+       uint16_t control;
+       int configured_private_bits;
+       int request_private_bits;
+       int irq;
+       int irq_step;
+       uint64_t search_mask;
+
+       /*
+        * Read the MSI config to figure out how many IRQs this device
+        * wants.  Most devices only want 1, which will give
+        * configured_private_bits and request_private_bits equal 0.
+        */
+       pci_read_config_word(dev, desc->msi_attrib.pos + PCI_MSI_FLAGS,
+                            &control);
+
+       /*
+        * If the number of private bits has been configured then use
+        * that value instead of the requested number. This gives the
+        * driver the chance to override the number of interrupts
+        * before calling pci_enable_msi().
+        */
+       configured_private_bits = (control & PCI_MSI_FLAGS_QSIZE) >> 4;
+       if (configured_private_bits == 0) {
+               /* Nothing is configured, so use the hardware requested size */
+               request_private_bits = (control & PCI_MSI_FLAGS_QMASK) >> 1;
+       } else {
+               /*
+                * Use the number of configured bits, assuming the
+                * driver wanted to override the hardware request
+                * value.
+                */
+               request_private_bits = configured_private_bits;
+       }
+
+       /*
+        * The PCI 2.3 spec mandates that there are at most 32
+        * interrupts. If this device asks for more, only give it one.
+        */
+       if (request_private_bits > 5)
+               request_private_bits = 0;
+
+try_only_one:
+       /*
+        * The IRQs have to be aligned on a power of two based on the
+        * number being requested.
+        */
+       irq_step = 1 << request_private_bits;
+
+       /* Mask with one bit for each IRQ */
+       search_mask = (1 << irq_step) - 1;
+
+       /*
+        * We're going to search msi_free_irq_bitmask_lock for zero
+        * bits. This represents an MSI interrupt number that isn't in
+        * use.
+        */
+       spin_lock(&msi_free_irq_bitmask_lock);
+       for (irq = 0; irq < 64; irq += irq_step) {
+               if ((msi_free_irq_bitmask & (search_mask << irq)) == 0) {
+                       msi_free_irq_bitmask |= search_mask << irq;
+                       msi_multiple_irq_bitmask |= (search_mask >> 1) << irq;
+                       break;
+               }
+       }
+       spin_unlock(&msi_free_irq_bitmask_lock);
+
+       /* Make sure the search for available interrupts didn't fail */
+       if (irq >= 64) {
+               if (request_private_bits) {
+                       pr_err("arch_setup_msi_irq: Unable to find %d free "
+                              "interrupts, trying just one",
+                              1 << request_private_bits);
+                       request_private_bits = 0;
+                       goto try_only_one;
+               } else
+                       panic("arch_setup_msi_irq: Unable to find a free MSI "
+                             "interrupt");
+       }
+
+       /* MSI interrupts start at logical IRQ OCTEON_IRQ_MSI_BIT0 */
+       irq += OCTEON_IRQ_MSI_BIT0;
+
+       switch (octeon_dma_bar_type) {
+       case OCTEON_DMA_BAR_TYPE_SMALL:
+               /* When not using big bar, Bar 0 is based at 128MB */
+               msg.address_lo =
+                       ((128ul << 20) + CVMX_PCI_MSI_RCV) & 0xffffffff;
+               msg.address_hi = ((128ul << 20) + CVMX_PCI_MSI_RCV) >> 32;
+       case OCTEON_DMA_BAR_TYPE_BIG:
+               /* When using big bar, Bar 0 is based at 0 */
+               msg.address_lo = (0 + CVMX_PCI_MSI_RCV) & 0xffffffff;
+               msg.address_hi = (0 + CVMX_PCI_MSI_RCV) >> 32;
+               break;
+       case OCTEON_DMA_BAR_TYPE_PCIE:
+               /* When using PCIe, Bar 0 is based at 0 */
+               /* FIXME CVMX_NPEI_MSI_RCV* other than 0? */
+               msg.address_lo = (0 + CVMX_NPEI_PCIE_MSI_RCV) & 0xffffffff;
+               msg.address_hi = (0 + CVMX_NPEI_PCIE_MSI_RCV) >> 32;
+               break;
+       default:
+               panic("arch_setup_msi_irq: Invalid octeon_dma_bar_type\n");
+       }
+       msg.data = irq - OCTEON_IRQ_MSI_BIT0;
+
+       /* Update the number of IRQs the device has available to it */
+       control &= ~PCI_MSI_FLAGS_QSIZE;
+       control |= request_private_bits << 4;
+       pci_write_config_word(dev, desc->msi_attrib.pos + PCI_MSI_FLAGS,
+                             control);
+
+       set_irq_msi(irq, desc);
+       write_msi_msg(irq, &msg);
+       return 0;
+}
+
+
+/**
+ * Called when a device no longer needs its MSI interrupts. All
+ * MSI interrupts for the device are freed.
+ *
+ * @irq:    The devices first irq number. There may be multple in sequence.
+ */
+void arch_teardown_msi_irq(unsigned int irq)
+{
+       int number_irqs;
+       uint64_t bitmask;
+
+       if ((irq < OCTEON_IRQ_MSI_BIT0) || (irq > OCTEON_IRQ_MSI_BIT63))
+               panic("arch_teardown_msi_irq: Attempted to teardown illegal "
+                     "MSI interrupt (%d)", irq);
+       irq -= OCTEON_IRQ_MSI_BIT0;
+
+       /*
+        * Count the number of IRQs we need to free by looking at the
+        * msi_multiple_irq_bitmask. Each bit set means that the next
+        * IRQ is also owned by this device.
+        */
+       number_irqs = 0;
+       while ((irq+number_irqs < 64) &&
+              (msi_multiple_irq_bitmask & (1ull << (irq + number_irqs))))
+               number_irqs++;
+       number_irqs++;
+       /* Mask with one bit for each IRQ */
+       bitmask = (1 << number_irqs) - 1;
+       /* Shift the mask to the correct bit location */
+       bitmask <<= irq;
+       if ((msi_free_irq_bitmask & bitmask) != bitmask)
+               panic("arch_teardown_msi_irq: Attempted to teardown MSI "
+                     "interrupt (%d) not in use", irq);
+
+       /* Checks are done, update the in use bitmask */
+       spin_lock(&msi_free_irq_bitmask_lock);
+       msi_free_irq_bitmask &= ~bitmask;
+       msi_multiple_irq_bitmask &= ~bitmask;
+       spin_unlock(&msi_free_irq_bitmask_lock);
+}
+
+
+/**
+ * Called by the interrupt handling code when an MSI interrupt
+ * occurs.
+ *
+ * @param cpl
+ * @param dev_id
+ *
+ * @return
+ */
+static irqreturn_t octeon_msi_interrupt(int cpl, void *dev_id)
+{
+       uint64_t msi_bits;
+       int irq;
+
+       if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_PCIE)
+               msi_bits = cvmx_read_csr(CVMX_PEXP_NPEI_MSI_RCV0);
+       else
+               msi_bits = cvmx_read_csr(CVMX_NPI_NPI_MSI_RCV);
+       irq = fls64(msi_bits);
+       if (irq) {
+               irq += OCTEON_IRQ_MSI_BIT0 - 1;
+               if (irq_desc[irq].action) {
+                       do_IRQ(irq);
+                       return IRQ_HANDLED;
+               } else {
+                       pr_err("Spurious MSI interrupt %d\n", irq);
+                       if (octeon_has_feature(OCTEON_FEATURE_PCIE)) {
+                               /* These chips have PCIe */
+                               cvmx_write_csr(CVMX_PEXP_NPEI_MSI_RCV0,
+                                              1ull << (irq -
+                                                       OCTEON_IRQ_MSI_BIT0));
+                       } else {
+                               /* These chips have PCI */
+                               cvmx_write_csr(CVMX_NPI_NPI_MSI_RCV,
+                                              1ull << (irq -
+                                                       OCTEON_IRQ_MSI_BIT0));
+                       }
+               }
+       }
+       return IRQ_NONE;
+}
+
+
+/**
+ * Initializes the MSI interrupt handling code
+ *
+ * @return
+ */
+int octeon_msi_initialize(void)
+{
+       int r;
+       if (octeon_has_feature(OCTEON_FEATURE_PCIE)) {
+               r = request_irq(OCTEON_IRQ_PCI_MSI0, octeon_msi_interrupt,
+                               IRQF_SHARED,
+                               "MSI[0:63]", octeon_msi_interrupt);
+       } else if (octeon_is_pci_host()) {
+               r = request_irq(OCTEON_IRQ_PCI_MSI0, octeon_msi_interrupt,
+                               IRQF_SHARED,
+                               "MSI[0:15]", octeon_msi_interrupt);
+               r += request_irq(OCTEON_IRQ_PCI_MSI1, octeon_msi_interrupt,
+                                IRQF_SHARED,
+                                "MSI[16:31]", octeon_msi_interrupt);
+               r += request_irq(OCTEON_IRQ_PCI_MSI2, octeon_msi_interrupt,
+                                IRQF_SHARED,
+                                "MSI[32:47]", octeon_msi_interrupt);
+               r += request_irq(OCTEON_IRQ_PCI_MSI3, octeon_msi_interrupt,
+                                IRQF_SHARED,
+                                "MSI[48:63]", octeon_msi_interrupt);
+       }
+       return 0;
+}
+
+subsys_initcall(octeon_msi_initialize);
diff --git a/arch/mips/cavium-octeon/octeon-irq.c 
b/arch/mips/cavium-octeon/octeon-irq.c
index 788d588..3d7be84 100644
--- a/arch/mips/cavium-octeon/octeon-irq.c
+++ b/arch/mips/cavium-octeon/octeon-irq.c
@@ -10,6 +10,8 @@
 #include <linux/hardirq.h>
 
 #include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+#include <asm/octeon/cvmx-npi-defs.h>
 
 DEFINE_RWLOCK(octeon_irq_ciu0_rwlock);
 DEFINE_RWLOCK(octeon_irq_ciu1_rwlock);
diff --git a/arch/mips/cavium-octeon/pci-common.c 
b/arch/mips/cavium-octeon/pci-common.c
new file mode 100644
index 0000000..cd029f8
--- /dev/null
+++ b/arch/mips/cavium-octeon/pci-common.c
@@ -0,0 +1,137 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2007 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include "pci-common.h"
+
+typeof(pcibios_map_irq) *octeon_pcibios_map_irq;
+enum octeon_dma_bar_type octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_INVALID;
+
+/**
+ * Map a PCI device to the appropriate interrupt line
+ *
+ * @param dev    The Linux PCI device structure for the device to map
+ * @param slot   The slot number for this device on __BUS 0__. Linux
+ *               enumerates through all the bridges and figures out the
+ *               slot on Bus 0 where this device eventually hooks to.
+ * @param pin    The PCI interrupt pin read from the device, then swizzled
+ *               as it goes through each bridge.
+ * @return Interrupt number for the device
+ */
+int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+       if (octeon_pcibios_map_irq)
+               return octeon_pcibios_map_irq(dev, slot, pin);
+       else
+               panic("octeon_pcibios_map_irq doesn't point to a "
+                     "pcibios_map_irq() function");
+}
+
+
+/**
+ * Called to perform platform specific PCI setup
+ *
+ * @param dev
+ * @return
+ */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+       uint16_t config;
+       uint32_t dconfig;
+       int pos;
+       /*
+        * Force the Cache line setting to 64 bytes. The standard
+        * Linux bus scan doesn't seem to set it. Octeon really has
+        * 128 byte lines, but Intel bridges get really upset if you
+        * try and set values above 64 bytes. Value is specified in
+        * 32bit words.
+        */
+       pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 64 / 4);
+       /* Set latency timers for all devices */
+       pci_write_config_byte(dev, PCI_LATENCY_TIMER, 48);
+
+       /* Enable reporting System errors and parity errors on all devices */
+       /* Enable parity checking and error reporting */
+       pci_read_config_word(dev, PCI_COMMAND, &config);
+       config |= PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
+       pci_write_config_word(dev, PCI_COMMAND, config);
+
+       if (dev->subordinate) {
+               /* Set latency timers on sub bridges */
+               pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER, 48);
+               /* More bridge error detection */
+               pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &config);
+               config |= PCI_BRIDGE_CTL_PARITY | PCI_BRIDGE_CTL_SERR;
+               pci_write_config_word(dev, PCI_BRIDGE_CONTROL, config);
+       }
+
+       /* Enable the PCIe normal error reporting */
+       pos = pci_find_capability(dev, PCI_CAP_ID_EXP);
+       if (pos) {
+               /* Update Device Control */
+               pci_read_config_word(dev, pos + PCI_EXP_DEVCTL, &config);
+               /* Correctable Error Reporting */
+               config |= PCI_EXP_DEVCTL_CERE;
+               /* Non-Fatal Error Reporting */
+               config |= PCI_EXP_DEVCTL_NFERE;
+               /* Fatal Error Reporting */
+               config |= PCI_EXP_DEVCTL_FERE;
+               /* Unsupported Request */
+               config |= PCI_EXP_DEVCTL_URRE;
+               pci_write_config_word(dev, pos + PCI_EXP_DEVCTL, config);
+       }
+
+       /* Find the Advanced Error Reporting capability */
+       pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR);
+       if (pos) {
+               /* Clear Uncorrectable Error Status */
+               pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_STATUS,
+                                     &dconfig);
+               pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_STATUS,
+                                      dconfig);
+               /* Enable reporting of all uncorrectable errors */
+               /* Uncorrectable Error Mask - turned on bits disable errors */
+               pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, 0);
+               /*
+                * Leave severity at HW default. This only controls if
+                * errors are reported as uncorrectable or
+                * correctable, not if the error is reported.
+                */
+               /* PCI_ERR_UNCOR_SEVER - Uncorrectable Error Severity */
+               /* Clear Correctable Error Status */
+               pci_read_config_dword(dev, pos + PCI_ERR_COR_STATUS, &dconfig);
+               pci_write_config_dword(dev, pos + PCI_ERR_COR_STATUS, dconfig);
+               /* Enable reporting of all correctable errors */
+               /* Correctable Error Mask - turned on bits disable errors */
+               pci_write_config_dword(dev, pos + PCI_ERR_COR_MASK, 0);
+               /* Advanced Error Capabilities */
+               pci_read_config_dword(dev, pos + PCI_ERR_CAP, &dconfig);
+               /* ECRC Generation Enable */
+               if (config & PCI_ERR_CAP_ECRC_GENC)
+                       config |= PCI_ERR_CAP_ECRC_GENE;
+               /* ECRC Check Enable */
+               if (config & PCI_ERR_CAP_ECRC_CHKC)
+                       config |= PCI_ERR_CAP_ECRC_CHKE;
+               pci_write_config_dword(dev, pos + PCI_ERR_CAP, dconfig);
+               /* PCI_ERR_HEADER_LOG - Header Log Register (16 bytes) */
+               /* Report all errors to the root complex */
+               pci_write_config_dword(dev, pos + PCI_ERR_ROOT_COMMAND,
+                                      PCI_ERR_ROOT_CMD_COR_EN |
+                                      PCI_ERR_ROOT_CMD_NONFATAL_EN |
+                                      PCI_ERR_ROOT_CMD_FATAL_EN);
+               /* Clear the Root status register */
+               pci_read_config_dword(dev, pos + PCI_ERR_ROOT_STATUS, &dconfig);
+               pci_write_config_dword(dev, pos + PCI_ERR_ROOT_STATUS, dconfig);
+       }
+
+       return 0;
+}
diff --git a/arch/mips/cavium-octeon/pci-common.h 
b/arch/mips/cavium-octeon/pci-common.h
new file mode 100644
index 0000000..74ae799
--- /dev/null
+++ b/arch/mips/cavium-octeon/pci-common.h
@@ -0,0 +1,39 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2007 Cavium Networks
+ */
+#ifndef __OCTEON_PCI_COMMON_H__
+#define __OCTEON_PCI_COMMON_H__
+
+#include <linux/pci.h>
+
+/* Some PCI cards require delays when accessing config space. */
+#define PCI_CONFIG_SPACE_DELAY 10000
+
+/* pcibios_map_irq() is defined inside pci-common.c. All it does is call the
+   Octeon specific version pointed to by this variable. This function needs to
+   change for PCI or PCIe based hosts */
+extern typeof(pcibios_map_irq) *octeon_pcibios_map_irq;
+
+/* The following defines are only used when octeon_dma_bar_type =
+   OCTEON_DMA_BAR_TYPE_BIG */
+#define OCTEON_PCI_BAR1_HOLE_BITS 5
+#define OCTEON_PCI_BAR1_HOLE_SIZE (1ul<<(OCTEON_PCI_BAR1_HOLE_BITS+3))
+
+enum octeon_dma_bar_type {
+       OCTEON_DMA_BAR_TYPE_INVALID,
+       OCTEON_DMA_BAR_TYPE_SMALL,
+       OCTEON_DMA_BAR_TYPE_BIG,
+       OCTEON_DMA_BAR_TYPE_PCIE
+};
+
+/**
+ * This is a variable to tell the DMA mapping system in dma-octeon.c
+ * how to map PCI DMA addresses.
+ */
+extern enum octeon_dma_bar_type octeon_dma_bar_type;
+
+#endif
diff --git a/arch/mips/cavium-octeon/pci.c b/arch/mips/cavium-octeon/pci.c
new file mode 100644
index 0000000..67c0ff5
--- /dev/null
+++ b/arch/mips/cavium-octeon/pci.c
@@ -0,0 +1,568 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2007 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+
+#include <asm/time.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-pci-defs.h>
+
+#include "pci-common.h"
+
+#define USE_OCTEON_INTERNAL_ARBITER
+
+/*
+ * Octeon's PCI controller uses did=3, subdid=2 for PCI IO
+ * addresses. Use PCI endian swapping 1 so no address swapping is
+ * necessary. The Linux io routines will endian swap the data.
+ */
+#define OCTEON_PCI_IOSPACE_BASE     0x80011a0400000000ull
+#define OCTEON_PCI_IOSPACE_SIZE     (1ull<<32)
+
+/* Octeon't PCI controller uses did=3, subdid=3 for PCI memory. */
+#define OCTEON_PCI_MEMSPACE_OFFSET  (0x00011b0000000000ull)
+
+/**
+ * This is the bit decoding used for the Octeon PCI controller addresses
+ */
+union octeon_pci_address {
+       uint64_t u64;
+       struct {
+               uint64_t upper:2;
+               uint64_t reserved:13;
+               uint64_t io:1;
+               uint64_t did:5;
+               uint64_t subdid:3;
+               uint64_t reserved2:4;
+               uint64_t endian_swap:2;
+               uint64_t reserved3:10;
+               uint64_t bus:8;
+               uint64_t dev:5;
+               uint64_t func:3;
+               uint64_t reg:8;
+       } s;
+};
+
+/**
+ * Return the mapping of PCI device number to IRQ line. Each
+ * character in the return string represents the interrupt
+ * line for the device at that position. Device 1 maps to the
+ * first character, etc. The characters A-D are used for PCI
+ * interrupts.
+ *
+ * Returns PCI interrupt mapping
+ */
+const char *octeon_get_pci_interrupts(void)
+{
+       /*
+        * Returning an empty string causes the interrupts to be
+        * routed based on the PCI specification. From the PCI spec:
+        *
+        * INTA# of Device Number 0 is connected to IRQW on the system
+        * board.  (Device Number has no significance regarding being
+        * located on the system board or in a connector.) INTA# of
+        * Device Number 1 is connected to IRQX on the system
+        * board. INTA# of Device Number 2 is connected to IRQY on the
+        * system board. INTA# of Device Number 3 is connected to IRQZ
+        * on the system board. The table below describes how each
+        * agent's INTx# lines are connected to the system board
+        * interrupt lines. The following equation can be used to
+        * determine to which INTx# signal on the system board a given
+        * device's INTx# line(s) is connected.
+        *
+        * MB = (D + I) MOD 4 MB = System board Interrupt (IRQW = 0,
+        * IRQX = 1, IRQY = 2, and IRQZ = 3) D = Device Number I =
+        * Interrupt Number (INTA# = 0, INTB# = 1, INTC# = 2, and
+        * INTD# = 3)
+        */
+       switch (octeon_bootinfo->board_type) {
+       case CVMX_BOARD_TYPE_NAO38:
+               /* This is really the NAC38 */
+               return "AAAAADABAAAAAAAAAAAAAAAAAAAAAAAA";
+       case CVMX_BOARD_TYPE_THUNDER:
+               return "";
+       case CVMX_BOARD_TYPE_EBH3000:
+               return "";
+       case CVMX_BOARD_TYPE_EBH3100:
+       case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
+       case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+               return "AAABAAAAAAAAAAAAAAAAAAAAAAAAAAAA";
+       case CVMX_BOARD_TYPE_BBGW_REF:
+               return "AABCD";
+       default:
+               return "";
+       }
+}
+
+/**
+ * Map a PCI device to the appropriate interrupt line
+ *
+ * @dev:    The Linux PCI device structure for the device to map
+ * @slot:   The slot number for this device on __BUS 0__. Linux
+ *               enumerates through all the bridges and figures out the
+ *               slot on Bus 0 where this device eventually hooks to.
+ * @pin:    The PCI interrupt pin read from the device, then swizzled
+ *               as it goes through each bridge.
+ * Returns Interrupt number for the device
+ */
+int __init octeon_pci_pcibios_map_irq(const struct pci_dev *dev,
+                                     u8 slot, u8 pin)
+{
+       int irq_num;
+       const char *interrupts;
+       int dev_num;
+
+       /* Get the board specific interrupt mapping */
+       interrupts = octeon_get_pci_interrupts();
+
+       dev_num = dev->devfn >> 3;
+       if (dev_num < strlen(interrupts))
+               irq_num = ((interrupts[dev_num] - 'A' + pin - 1) & 3) +
+                       OCTEON_IRQ_PCI_INT0;
+       else
+               irq_num = ((slot + pin - 3) & 3) + OCTEON_IRQ_PCI_INT0;
+       return irq_num;
+}
+
+
+/**
+ * Read a value from configuration space
+ *
+ */
+static int octeon_read_config(struct pci_bus *bus, unsigned int devfn,
+                             int reg, int size, u32 *val)
+{
+       union octeon_pci_address pci_addr;
+
+       pci_addr.u64 = 0;
+       pci_addr.s.upper = 2;
+       pci_addr.s.io = 1;
+       pci_addr.s.did = 3;
+       pci_addr.s.subdid = 1;
+       pci_addr.s.endian_swap = 1;
+       pci_addr.s.bus = bus->number;
+       pci_addr.s.dev = devfn >> 3;
+       pci_addr.s.func = devfn & 0x7;
+       pci_addr.s.reg = reg;
+
+#if PCI_CONFIG_SPACE_DELAY
+       udelay(PCI_CONFIG_SPACE_DELAY);
+#endif
+       switch (size) {
+       case 4:
+               *val = le32_to_cpu(cvmx_read64_uint32(pci_addr.u64));
+               return PCIBIOS_SUCCESSFUL;
+       case 2:
+               *val = le16_to_cpu(cvmx_read64_uint16(pci_addr.u64));
+               return PCIBIOS_SUCCESSFUL;
+       case 1:
+               *val = cvmx_read64_uint8(pci_addr.u64);
+               return PCIBIOS_SUCCESSFUL;
+       }
+       return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+
+/**
+ * Write a value to PCI configuration space
+ *
+ * @bus:
+ * @devfn:
+ * @reg:
+ * @size:
+ * @val:
+ * Returns
+ */
+static int octeon_write_config(struct pci_bus *bus, unsigned int devfn,
+                              int reg, int size, u32 val)
+{
+       union octeon_pci_address pci_addr;
+
+       pci_addr.u64 = 0;
+       pci_addr.s.upper = 2;
+       pci_addr.s.io = 1;
+       pci_addr.s.did = 3;
+       pci_addr.s.subdid = 1;
+       pci_addr.s.endian_swap = 1;
+       pci_addr.s.bus = bus->number;
+       pci_addr.s.dev = devfn >> 3;
+       pci_addr.s.func = devfn & 0x7;
+       pci_addr.s.reg = reg;
+
+#if PCI_CONFIG_SPACE_DELAY
+       udelay(PCI_CONFIG_SPACE_DELAY);
+#endif
+       switch (size) {
+       case 4:
+               cvmx_write64_uint32(pci_addr.u64, cpu_to_le32(val));
+               return PCIBIOS_SUCCESSFUL;
+       case 2:
+               cvmx_write64_uint16(pci_addr.u64, cpu_to_le16(val));
+               return PCIBIOS_SUCCESSFUL;
+       case 1:
+               cvmx_write64_uint8(pci_addr.u64, val);
+               return PCIBIOS_SUCCESSFUL;
+       }
+       return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+
+static struct pci_ops octeon_pci_ops = {
+       octeon_read_config,
+       octeon_write_config,
+};
+
+static struct resource octeon_pci_mem_resource = {
+       .start = 0,
+       .end = 0,
+       .name = "Octeon PCI MEM",
+       .flags = IORESOURCE_MEM,
+};
+
+/*
+ * PCI ports must be above 16KB so the ISA bus filtering in the PCI-X to PCI
+ * bridge
+ */
+static struct resource octeon_pci_io_resource = {
+       .start = 0x4000,
+       .end = OCTEON_PCI_IOSPACE_SIZE - 1,
+       .name = "Octeon PCI IO",
+       .flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_pci_controller = {
+       .pci_ops = &octeon_pci_ops,
+       .mem_resource = &octeon_pci_mem_resource,
+       .mem_offset = OCTEON_PCI_MEMSPACE_OFFSET,
+       .io_resource = &octeon_pci_io_resource,
+       .io_offset = 0,
+       .io_map_base = OCTEON_PCI_IOSPACE_BASE,
+};
+
+
+/**
+ * Low level initialize the Octeon PCI controller
+ *
+ * Returns
+ */
+static void octeon_pci_initialize(void)
+{
+       union cvmx_pci_cfg01 cfg01;
+       union cvmx_npi_ctl_status ctl_status;
+       union cvmx_pci_ctl_status_2 ctl_status_2;
+       union cvmx_pci_cfg19 cfg19;
+       union cvmx_pci_cfg16 cfg16;
+       union cvmx_pci_cfg22 cfg22;
+       union cvmx_pci_cfg56 cfg56;
+
+       /* Reset the PCI Bus */
+       cvmx_write_csr(CVMX_CIU_SOFT_PRST, 0x1);
+       cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+
+       udelay(2000);           /* Hold PCI reset for 2 ms */
+
+       ctl_status.u64 = 0;     /* cvmx_read_csr(CVMX_NPI_CTL_STATUS); */
+       ctl_status.s.max_word = 1;
+       ctl_status.s.timer = 1;
+       cvmx_write_csr(CVMX_NPI_CTL_STATUS, ctl_status.u64);
+
+       /* Deassert PCI reset and advertize PCX Host Mode Device Capability
+          (64b) */
+       cvmx_write_csr(CVMX_CIU_SOFT_PRST, 0x4);
+       cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+
+       udelay(2000);           /* Wait 2 ms after deasserting PCI reset */
+
+       ctl_status_2.u32 = 0;
+       ctl_status_2.s.tsr_hwm = 1;     /* Initializes to 0.  Must be set
+                                          before any PCI reads. */
+       ctl_status_2.s.bar2pres = 1;    /* Enable BAR2 */
+       ctl_status_2.s.bar2_enb = 1;
+       ctl_status_2.s.bar2_cax = 1;    /* Don't use L2 */
+       ctl_status_2.s.bar2_esx = 1;
+       ctl_status_2.s.pmo_amod = 1;    /* Round robin priority */
+       if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG) {
+               /* BAR1 hole */
+               ctl_status_2.s.bb1_hole = OCTEON_PCI_BAR1_HOLE_BITS;
+               ctl_status_2.s.bb1_siz = 1;  /* BAR1 is 2GB */
+               ctl_status_2.s.bb_ca = 1;    /* Don't use L2 with big bars */
+               ctl_status_2.s.bb_es = 1;    /* Big bar in byte swap mode */
+               ctl_status_2.s.bb1 = 1;      /* BAR1 is big */
+               ctl_status_2.s.bb0 = 1;      /* BAR0 is big */
+       }
+
+       octeon_npi_write32(CVMX_NPI_PCI_CTL_STATUS_2, ctl_status_2.u32);
+       udelay(2000);           /* Wait 2 ms before doing PCI reads */
+
+       ctl_status_2.u32 = octeon_npi_read32(CVMX_NPI_PCI_CTL_STATUS_2);
+       pr_notice("PCI Status: %s %s-bit\n",
+                 ctl_status_2.s.ap_pcix ? "PCI-X" : "PCI",
+                 ctl_status_2.s.ap_64ad ? "64" : "32");
+
+       if (OCTEON_IS_MODEL(OCTEON_CN58XX) || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+               union cvmx_pci_cnt_reg cnt_reg_start;
+               union cvmx_pci_cnt_reg cnt_reg_end;
+               unsigned long cycles, pci_clock;
+
+               cnt_reg_start.u64 = cvmx_read_csr(CVMX_NPI_PCI_CNT_REG);
+               cycles = read_c0_cvmcount();
+               udelay(1000);
+               cnt_reg_end.u64 = cvmx_read_csr(CVMX_NPI_PCI_CNT_REG);
+               cycles = read_c0_cvmcount() - cycles;
+               pci_clock = (cnt_reg_end.s.pcicnt - cnt_reg_start.s.pcicnt) /
+                           (cycles / (mips_hpt_frequency / 1000000));
+               pr_notice("PCI Clock: %lu MHz\n", pci_clock);
+       }
+
+       /*
+        * TDOMC must be set to one in PCI mode. TDOMC should be set to 4
+        * in PCI-X mode to allow four oustanding splits. Otherwise,
+        * should not change from its reset value. Don't write PCI_CFG19
+        * in PCI mode (0x82000001 reset value), write it to 0x82000004
+        * after PCI-X mode is known. MRBCI,MDWE,MDRE -> must be zero.
+        * MRBCM -> must be one.
+        */
+       if (ctl_status_2.s.ap_pcix) {
+               cfg19.u32 = 0;
+               /*
+                * Target Delayed/Split request outstanding maximum
+                * count. [1..31] and 0=32.  NOTE: If the user
+                * programs these bits beyond the Designed Maximum
+                * outstanding count, then the designed maximum table
+                * depth will be used instead.  No additional
+                * Deferred/Split transactions will be accepted if
+                * this outstanding maximum count is
+                * reached. Furthermore, no additional deferred/split
+                * transactions will be accepted if the I/O delay/ I/O
+                * Split Request outstanding maximum is reached.
+                */
+               cfg19.s.tdomc = 4;
+               /*
+                * Master Deferred Read Request Outstanding Max Count
+                * (PCI only).  CR4C[26:24] Max SAC cycles MAX DAC
+                * cycles 000 8 4 001 1 0 010 2 1 011 3 1 100 4 2 101
+                * 5 2 110 6 3 111 7 3 For example, if these bits are
+                * programmed to 100, the core can support 2 DAC
+                * cycles, 4 SAC cycles or a combination of 1 DAC and
+                * 2 SAC cycles. NOTE: For the PCI-X maximum
+                * outstanding split transactions, refer to
+                * CRE0[22:20].
+                */
+               cfg19.s.mdrrmc = 2;
+               /*
+                * Master Request (Memory Read) Byte Count/Byte Enable
+                * select. 0 = Byte Enables valid. In PCI mode, a
+                * burst transaction cannot be performed using Memory
+                * Read command=4?h6. 1 = DWORD Byte Count valid
+                * (default). In PCI Mode, the memory read byte
+                * enables are automatically generated by the
+                * core. Note: N3 Master Request transaction sizes are
+                * always determined through the
+                * am_attr[<35:32>|<7:0>] field.
+                */
+               cfg19.s.mrbcm = 1;
+               octeon_npi_write32(CVMX_NPI_PCI_CFG19, cfg19.u32);
+       }
+
+
+       cfg01.u32 = 0;
+       cfg01.s.msae = 1;       /* Memory Space Access Enable */
+       cfg01.s.me = 1;         /* Master Enable */
+       cfg01.s.pee = 1;        /* PERR# Enable */
+       cfg01.s.see = 1;        /* System Error Enable */
+       cfg01.s.fbbe = 1;       /* Fast Back to Back Transaction Enable */
+
+       octeon_npi_write32(CVMX_NPI_PCI_CFG01, cfg01.u32);
+
+#ifdef USE_OCTEON_INTERNAL_ARBITER
+       /*
+        * When OCTEON is a PCI host, most systems will use OCTEON's
+        * internal arbiter, so must enable it before any PCI/PCI-X
+        * traffic can occur.
+        */
+       {
+               union cvmx_npi_pci_int_arb_cfg pci_int_arb_cfg;
+
+               pci_int_arb_cfg.u64 = 0;
+               pci_int_arb_cfg.s.en = 1;       /* Internal arbiter enable */
+               cvmx_write_csr(CVMX_NPI_PCI_INT_ARB_CFG, pci_int_arb_cfg.u64);
+       }
+#endif                         /* USE_OCTEON_INTERNAL_ARBITER */
+
+       /*
+        * Preferrably written to 1 to set MLTD. [RDSATI,TRTAE,
+        * TWTAE,TMAE,DPPMR -> must be zero. TILT -> must not be set to
+        * 1..7.
+        */
+       cfg16.u32 = 0;
+       cfg16.s.mltd = 1;       /* Master Latency Timer Disable */
+       octeon_npi_write32(CVMX_NPI_PCI_CFG16, cfg16.u32);
+
+       /*
+        * Should be written to 0x4ff00. MTTV -> must be zero.
+        * FLUSH -> must be 1. MRV -> should be 0xFF.
+        */
+       cfg22.u32 = 0;
+       /* Master Retry Value [1..255] and 0=infinite */
+       cfg22.s.mrv = 0xff;
+       /*
+        * AM_DO_FLUSH_I control NOTE: This bit MUST BE ONE for proper
+        * N3K operation.
+        */
+       cfg22.s.flush = 1;
+       octeon_npi_write32(CVMX_NPI_PCI_CFG22, cfg22.u32);
+
+       /*
+        * MOST Indicates the maximum number of outstanding splits (in -1
+        * notation) when OCTEON is in PCI-X mode.  PCI-X performance is
+        * affected by the MOST selection.  Should generally be written
+        * with one of 0x3be807, 0x2be807, 0x1be807, or 0x0be807,
+        * depending on the desired MOST of 3, 2, 1, or 0, respectively.
+        */
+       cfg56.u32 = 0;
+       cfg56.s.pxcid = 7;      /* RO - PCI-X Capability ID */
+       cfg56.s.ncp = 0xe8;     /* RO - Next Capability Pointer */
+       cfg56.s.dpere = 1;      /* Data Parity Error Recovery Enable */
+       cfg56.s.roe = 1;        /* Relaxed Ordering Enable */
+       cfg56.s.mmbc = 1;       /* Maximum Memory Byte Count
+                                  [0=512B,1=1024B,2=2048B,3=4096B] */
+       cfg56.s.most = 3;       /* Maximum outstanding Split transactions [0=1
+                                  .. 7=32] */
+
+       octeon_npi_write32(CVMX_NPI_PCI_CFG56, cfg56.u32);
+
+       /*
+        * Affects PCI performance when OCTEON services reads to its
+        * BAR1/BAR2. Refer to Section 10.6.1.  The recommended values are
+        * 0x22, 0x33, and 0x33 for PCI_READ_CMD_6, PCI_READ_CMD_C, and
+        * PCI_READ_CMD_E, respectively. Unfortunately due to errata DDR-700,
+        * these values need to be changed so they won't possibly prefetch off
+        * of the end of memory if PCI is DMAing a buffer at the end of
+        * memory. Note that these values differ from their reset values.
+        */
+       octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_6, 0x21);
+       octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_C, 0x31);
+       octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_E, 0x31);
+}
+
+
+/**
+ * Initialize the Octeon PCI controller
+ *
+ * Returns
+ */
+static int __init octeon_pci_setup(void)
+{
+       union cvmx_npi_mem_access_subidx mem_access;
+       int index;
+
+       /* Only these chips have PCI */
+       if (octeon_has_feature(OCTEON_FEATURE_PCIE))
+               return 0;
+
+       /* Point pcibios_map_irq() to the PCI version of it */
+       octeon_pcibios_map_irq = octeon_pci_pcibios_map_irq;
+
+       /* Only use the big bars on chips that support it */
+       if (OCTEON_IS_MODEL(OCTEON_CN31XX) ||
+           OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2) ||
+           OCTEON_IS_MODEL(OCTEON_CN38XX_PASS1))
+               octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_SMALL;
+       else
+               octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_BIG;
+
+       /* PCI I/O and PCI MEM values */
+       set_io_port_base(OCTEON_PCI_IOSPACE_BASE);
+       ioport_resource.start = 0;
+       ioport_resource.end = OCTEON_PCI_IOSPACE_SIZE - 1;
+       if (!octeon_is_pci_host()) {
+               pr_notice("Not in host mode, PCI Controller not initialized\n");
+               return 0;
+       }
+
+       pr_notice("%s Octeon big bar support\n",
+                 (octeon_dma_bar_type ==
+                 OCTEON_DMA_BAR_TYPE_BIG) ? "Enabling" : "Disabling");
+
+       octeon_pci_initialize();
+
+       mem_access.u64 = 0;
+       mem_access.s.esr = 1;   /* Endian-Swap on read. */
+       mem_access.s.esw = 1;   /* Endian-Swap on write. */
+       mem_access.s.nsr = 0;   /* No-Snoop on read. */
+       mem_access.s.nsw = 0;   /* No-Snoop on write. */
+       mem_access.s.ror = 0;   /* Relax Read on read. */
+       mem_access.s.row = 0;   /* Relax Order on write. */
+       mem_access.s.ba = 0;    /* PCI Address bits [63:36]. */
+       cvmx_write_csr(CVMX_NPI_MEM_ACCESS_SUBID3, mem_access.u64);
+
+       /*
+        * Remap the Octeon BAR 2 above all 32 bit devices
+        * (0x8000000000ul).  This is done here so it is remapped
+        * before the readl()'s below. We don't want BAR2 overlapping
+        * with BAR0/BAR1 during these reads.
+        */
+       octeon_npi_write32(CVMX_NPI_PCI_CFG08, 0);
+       octeon_npi_write32(CVMX_NPI_PCI_CFG09, 0x80);
+
+       /* Disable the BAR1 movable mappings */
+       for (index = 0; index < 32; index++)
+               octeon_npi_write32(CVMX_NPI_PCI_BAR1_INDEXX(index), 0);
+
+       if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG) {
+               /* Remap the Octeon BAR 0 to 0-2GB */
+               octeon_npi_write32(CVMX_NPI_PCI_CFG04, 0);
+               octeon_npi_write32(CVMX_NPI_PCI_CFG05, 0);
+
+               /*
+                * Remap the Octeon BAR 1 to map 2GB-4GB (minus the
+                * BAR 1 hole).
+                */
+               octeon_npi_write32(CVMX_NPI_PCI_CFG06, 2ul << 30);
+               octeon_npi_write32(CVMX_NPI_PCI_CFG07, 0);
+
+               /* Devices go after BAR1 */
+               octeon_pci_mem_resource.start =
+                       OCTEON_PCI_MEMSPACE_OFFSET + (4ul << 30) -
+                       (OCTEON_PCI_BAR1_HOLE_SIZE << 20);
+               octeon_pci_mem_resource.end =
+                       octeon_pci_mem_resource.start + (1ul << 30);
+       } else {
+               /* Remap the Octeon BAR 0 to map 128MB-(128MB+4KB) */
+               octeon_npi_write32(CVMX_NPI_PCI_CFG04, 128ul << 20);
+               octeon_npi_write32(CVMX_NPI_PCI_CFG05, 0);
+
+               /* Remap the Octeon BAR 1 to map 0-128MB */
+               octeon_npi_write32(CVMX_NPI_PCI_CFG06, 0);
+               octeon_npi_write32(CVMX_NPI_PCI_CFG07, 0);
+
+               /* Devices go after BAR0 */
+               octeon_pci_mem_resource.start =
+                       OCTEON_PCI_MEMSPACE_OFFSET + (128ul << 20) +
+                       (4ul << 10);
+               octeon_pci_mem_resource.end =
+                       octeon_pci_mem_resource.start + (1ul << 30);
+       }
+
+       register_pci_controller(&octeon_pci_controller);
+
+       /*
+        * Clear any errors that might be pending from before the bus
+        * was setup properly.
+        */
+       cvmx_write_csr(CVMX_NPI_PCI_INT_SUM2, -1);
+       return 0;
+}
+
+arch_initcall(octeon_pci_setup);
diff --git a/arch/mips/cavium-octeon/pcie.c b/arch/mips/cavium-octeon/pcie.c
new file mode 100644
index 0000000..cb6662c
--- /dev/null
+++ b/arch/mips/cavium-octeon/pcie.c
@@ -0,0 +1,441 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007, 2008 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-pcie.h>
+#include <asm/octeon/cvmx-npei-defs.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+
+#include "pci-common.h"
+
+/**
+ * Map a PCI device to the appropriate interrupt line
+ *
+ * @param dev    The Linux PCI device structure for the device to map
+ * @param slot   The slot number for this device on __BUS 0__. Linux
+ *               enumerates through all the bridges and figures out the
+ *               slot on Bus 0 where this device eventually hooks to.
+ * @param pin    The PCI interrupt pin read from the device, then swizzled
+ *               as it goes through each bridge.
+ * @return Interrupt number for the device
+ */
+int __init octeon_pcie_pcibios_map_irq(const struct pci_dev *dev,
+                                      u8 slot, u8 pin)
+{
+       /*
+        * The EBH5600 board with the PCI to PCIe bridge mistakenly
+        * wires the first slot for both device id 2 and interrupt
+        * A. According to the PCI spec, device id 2 should be C. The
+        * following kludge attempts to fix this.
+        */
+       if (strstr(octeon_board_type_string(), "EBH5600") &&
+           dev->bus && dev->bus->parent) {
+               /*
+                * Iterate all the way up the device chain and find
+                * the root bus.
+                */
+               while (dev->bus && dev->bus->parent)
+                       dev = to_pci_dev(dev->bus->bridge);
+               /* If the root bus is number 0 and the PEX 8114 is the
+                * root, assume we are behind the miswired bus. We
+                * need to correct the swizzle level by two. Yuck.
+                */
+               if ((dev->bus->number == 0) &&
+                   (dev->vendor == 0x10b5) && (dev->device == 0x8114)) {
+                       /*
+                        * The pin field is one based, not zero. We
+                        * need to swizzle it by minus two.
+                        */
+                       pin = ((pin - 3) & 3) + 1;
+               }
+       }
+       /*
+        * The -1 is because pin starts with one, not zero. It might
+        * be that this equation needs to include the slot number, but
+        * I don't have hardware to check that against.
+        */
+       return pin - 1 + OCTEON_IRQ_PCI_INT0;
+}
+
+/**
+ * Read a value from configuration space
+ *
+ * @param bus
+ * @param devfn
+ * @param reg
+ * @param size
+ * @param val
+ * @return
+ */
+static inline int octeon_pcie_read_config(int pcie_port, struct pci_bus *bus,
+                                         unsigned int devfn, int reg, int size,
+                                         u32 *val)
+{
+       union octeon_cvmemctl cvmmemctl;
+       union octeon_cvmemctl cvmmemctl_save;
+       int bus_number = bus->number;
+
+       /*
+        * We need to force the bus number to be zero on the root
+        * bus. Linux numbers the 2nd root bus to start after all
+        * buses on root 0.
+        */
+       if (bus->parent == NULL)
+               bus_number = 0;
+
+       /*
+        * PCIe only has a single device connected to Octeon. It is
+        * always device ID 0. Don't bother doing reads for other
+        * device IDs on the first segment.
+        */
+       if ((bus_number == 0) && (devfn >> 3 != 0))
+               return PCIBIOS_FUNC_NOT_SUPPORTED;
+
+       /*
+        * The following is a workaround for the CN57XX, CN56XX,
+        * CN55XX, and CN54XX errata with PCIe config reads from non
+        * existent devices.  These chips will hang the PCIe link if a
+        * config read is performed that causes a UR response.
+        */
+       if (OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1) ||
+           OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_1)) {
+               /*
+                * For our EBH5600 board, port 0 has a bridge with two
+                * PCI-X slots. We need a new special checks to make
+                * sure we only probe valid stuff.  The PCIe->PCI-X
+                * bridge only respondes to device ID 0, function
+                * 0-1
+                */
+               if ((bus_number == 0) && (devfn >= 2))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+               /*
+                * The PCI-X slots are device ID 2,3. Choose one of
+                * the below "if" blocks based on what is plugged into
+                * the board.
+                */
+#if 1
+               /* Use this option if you aren't using either slot */
+               if (bus_number == 1)
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+#elif 0
+               /*
+                * Use this option if you are using the first slot but
+                * not the second.
+                */
+               if ((bus_number == 1) && (devfn >> 3 != 2))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+#elif 0
+               /*
+                * Use this option if you are using the second slot
+                * but not the first.
+                */
+               if ((bus_number == 1) && (devfn >> 3 != 3))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+#elif 0
+               /* Use this opion if you are using both slots */
+               if ((bus_number == 1) &&
+                   !((devfn == (2 << 3)) || (devfn == (3 << 3))))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+#endif
+
+               /*
+                * The following #if gives a more complicated
+                * example. This is the required checks for running a
+                * Nitrox CN16XX-NHBX in the slot of the EBH5600. This
+                * card has a PLX PCIe bridge with four Nitrox PLX
+                * parts behind it.
+                */
+#if 0
+               /* PLX bridge with 4 ports */
+               if ((bus_number == 3) &&
+                   !((devfn >> 3 >= 1) && (devfn >> 3 <= 4)))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+               /* Nitrox behind PLX 1 */
+               if ((bus_number == 4) && (devfn >> 3 != 0))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+               /* Nitrox behind PLX 2 */
+               if ((bus_number == 5) && (devfn >> 3 != 0))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+               /* Nitrox behind PLX 3 */
+               if ((bus_number == 6) && (devfn >> 3 != 0))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+               /* Nitrox behind PLX 4 */
+               if ((bus_number == 7) && (devfn >> 3 != 0))
+                       return PCIBIOS_FUNC_NOT_SUPPORTED;
+#endif
+               /*
+                * Shorten the DID timeout so bus errors for PCIe
+                * config reads from non existent devices happen
+                * faster. This allows us to continue booting even if
+                * the above "if" checks are wrong.  Once one of these
+                * errors happens, the PCIe port is dead.
+                */
+               cvmmemctl_save.u64 = __read_64bit_c0_register($11, 7);
+               cvmmemctl.u64 = cvmmemctl_save.u64;
+               cvmmemctl.s.didtto = 2;
+               __write_64bit_c0_register($11, 7, cvmmemctl.u64);
+       }
+
+       switch (size) {
+       case 4:
+               *val = cvmx_pcie_config_read32(pcie_port, bus_number,
+                                              devfn >> 3, devfn & 0x7, reg);
+               break;
+       case 2:
+               *val = cvmx_pcie_config_read16(pcie_port, bus_number,
+                                              devfn >> 3, devfn & 0x7, reg);
+               break;
+       case 1:
+               *val = cvmx_pcie_config_read8(pcie_port, bus_number, devfn >> 3,
+                                             devfn & 0x7, reg);
+               break;
+       default:
+               return PCIBIOS_FUNC_NOT_SUPPORTED;
+       }
+
+       if (OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1) ||
+           OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_1))
+               __write_64bit_c0_register($11, 7, cvmmemctl_save.u64);
+       return PCIBIOS_SUCCESSFUL;
+}
+
+static int octeon_pcie0_read_config(struct pci_bus *bus, unsigned int devfn,
+                                   int reg, int size, u32 *val)
+{
+       return octeon_pcie_read_config(0, bus, devfn, reg, size, val);
+}
+
+static int octeon_pcie1_read_config(struct pci_bus *bus, unsigned int devfn,
+                                   int reg, int size, u32 *val)
+{
+       return octeon_pcie_read_config(1, bus, devfn, reg, size, val);
+}
+
+
+
+/**
+ * Write a value to PCI configuration space
+ *
+ * @param bus
+ * @param devfn
+ * @param reg
+ * @param size
+ * @param val
+ * @return
+ */
+static inline int octeon_pcie_write_config(int pcie_port, struct pci_bus *bus,
+                                          unsigned int devfn, int reg,
+                                          int size, u32 val)
+{
+       int bus_number = bus->number;
+       /*
+        * We need to force the bus number to be zero on the root
+        * bus. Linux numbers the 2nd root bus to start after all
+        * busses on root 0.
+        */
+       if (bus->parent == NULL)
+               bus_number = 0;
+
+       switch (size) {
+       case 4:
+               cvmx_pcie_config_write32(pcie_port, bus_number, devfn >> 3,
+                                        devfn & 0x7, reg, val);
+               return PCIBIOS_SUCCESSFUL;
+       case 2:
+               cvmx_pcie_config_write16(pcie_port, bus_number, devfn >> 3,
+                                        devfn & 0x7, reg, val);
+               return PCIBIOS_SUCCESSFUL;
+       case 1:
+               cvmx_pcie_config_write8(pcie_port, bus_number, devfn >> 3,
+                                       devfn & 0x7, reg, val);
+               return PCIBIOS_SUCCESSFUL;
+       }
+#if PCI_CONFIG_SPACE_DELAY
+       udelay(PCI_CONFIG_SPACE_DELAY);
+#endif
+       return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+static int octeon_pcie0_write_config(struct pci_bus *bus, unsigned int devfn,
+                                    int reg, int size, u32 val)
+{
+       return octeon_pcie_write_config(0, bus, devfn, reg, size, val);
+}
+
+static int octeon_pcie1_write_config(struct pci_bus *bus, unsigned int devfn,
+                                    int reg, int size, u32 val)
+{
+       return octeon_pcie_write_config(1, bus, devfn, reg, size, val);
+}
+
+static struct pci_ops octeon_pcie0_ops = {
+       octeon_pcie0_read_config,
+       octeon_pcie0_write_config,
+};
+
+static struct resource octeon_pcie0_mem_resource = {
+       .name = "Octeon PCIe0 MEM",
+       .flags = IORESOURCE_MEM,
+};
+
+static struct resource octeon_pcie0_io_resource = {
+       .name = "Octeon PCIe0 IO",
+       .flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_pcie0_controller = {
+       .pci_ops = &octeon_pcie0_ops,
+       .mem_resource = &octeon_pcie0_mem_resource,
+       .io_resource = &octeon_pcie0_io_resource,
+};
+
+static struct pci_ops octeon_pcie1_ops = {
+       octeon_pcie1_read_config,
+       octeon_pcie1_write_config,
+};
+
+static struct resource octeon_pcie1_mem_resource = {
+       .name = "Octeon PCIe1 MEM",
+       .flags = IORESOURCE_MEM,
+};
+
+static struct resource octeon_pcie1_io_resource = {
+       .name = "Octeon PCIe1 IO",
+       .flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_pcie1_controller = {
+       .pci_ops = &octeon_pcie1_ops,
+       .mem_resource = &octeon_pcie1_mem_resource,
+       .io_resource = &octeon_pcie1_io_resource,
+};
+
+
+/**
+ * Initialize the Octeon PCIe controllers
+ *
+ * @return
+ */
+static int __init octeon_pcie_setup(void)
+{
+       union cvmx_npei_ctl_status npei_ctl_status;
+       int result;
+
+       /* These chips don't have PCIe */
+       if (!octeon_has_feature(OCTEON_FEATURE_PCIE))
+               return 0;
+
+       /* Point pcibios_map_irq() to the PCIe version of it */
+       octeon_pcibios_map_irq = octeon_pcie_pcibios_map_irq;
+
+       /* Use the PCIe based DMA mappings */
+       octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_PCIE;
+
+       /*
+        * PCIe I/O range. It is based on port 0 but includes up until
+        * port 1's end.
+        */
+       set_io_port_base(CVMX_ADD_IO_SEG(cvmx_pcie_get_io_base_address(0)));
+       ioport_resource.start = 0;
+       ioport_resource.end =
+               cvmx_pcie_get_io_base_address(1) -
+               cvmx_pcie_get_io_base_address(0) + cvmx_pcie_get_io_size(1) - 1;
+
+       npei_ctl_status.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS);
+       if (npei_ctl_status.s.host_mode) {
+               pr_notice("PCIe: Initializing port 0\n");
+               result = cvmx_pcie_rc_initialize(0);
+               if (result == 0) {
+                       /* Memory offsets are physical addresses */
+                       octeon_pcie0_controller.mem_offset =
+                               cvmx_pcie_get_mem_base_address(0);
+                       /* IO offsets are Mips virtual addresses */
+                       octeon_pcie0_controller.io_map_base =
+                               CVMX_ADD_IO_SEG(cvmx_pcie_get_io_base_address
+                                               (0));
+                       octeon_pcie0_controller.io_offset = 0;
+                       /*
+                        * To keep things similar to PCI, we start
+                        * device addresses at the same place as PCI
+                        * uisng big bar support. This normally
+                        * translates to 4GB-256MB, which is the same
+                        * as most x86 PCs.
+                        */
+                       octeon_pcie0_controller.mem_resource->start =
+                               cvmx_pcie_get_mem_base_address(0) +
+                               (4ul << 30) - (OCTEON_PCI_BAR1_HOLE_SIZE << 20);
+                       octeon_pcie0_controller.mem_resource->end =
+                               cvmx_pcie_get_mem_base_address(0) +
+                               cvmx_pcie_get_mem_size(0) - 1;
+                       /*
+                        * Ports must be above 16KB for the ISA bus
+                        * filtering in the PCI-X to PCI bridge.
+                        */
+                       octeon_pcie0_controller.io_resource->start = 4 << 10;
+                       octeon_pcie0_controller.io_resource->end =
+                               cvmx_pcie_get_io_size(0) - 1;
+                       register_pci_controller(&octeon_pcie0_controller);
+               }
+       } else {
+               pr_notice("PCIe: Port 0 in endpoint mode, skipping.\n");
+       }
+
+       /* Skip the 2nd port on CN52XX if port 0 is in 4 lane mode */
+       if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+               union cvmx_npei_dbg_data npei_dbg_data;
+               npei_dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+               if (npei_dbg_data.cn52xx.qlm0_link_width)
+                       return 0;
+       }
+
+       pr_notice("PCIe: Initializing port 1\n");
+       result = cvmx_pcie_rc_initialize(1);
+       if (result == 0) {
+               /* Memory offsets are physical addresses */
+               octeon_pcie1_controller.mem_offset =
+                       cvmx_pcie_get_mem_base_address(1);
+               /* IO offsets are Mips virtual addresses */
+               octeon_pcie1_controller.io_map_base =
+                       CVMX_ADD_IO_SEG(cvmx_pcie_get_io_base_address(1));
+               octeon_pcie1_controller.io_offset =
+                       cvmx_pcie_get_io_base_address(1) -
+                       cvmx_pcie_get_io_base_address(0);
+               /*
+                * To keep things similar to PCI, we start device
+                * addresses at the same place as PCI uisng big bar
+                * support. This normally translates to 4GB-256MB,
+                * which is the same as most x86 PCs.
+                */
+               octeon_pcie1_controller.mem_resource->start =
+                       cvmx_pcie_get_mem_base_address(1) + (4ul << 30) -
+                       (OCTEON_PCI_BAR1_HOLE_SIZE << 20);
+               octeon_pcie1_controller.mem_resource->end =
+                       cvmx_pcie_get_mem_base_address(1) +
+                       cvmx_pcie_get_mem_size(1) - 1;
+               /*
+                * Ports must be above 16KB for the ISA bus filtering
+                * in the PCI-X to PCI bridge.
+                */
+               octeon_pcie1_controller.io_resource->start =
+                       cvmx_pcie_get_io_base_address(1) -
+                       cvmx_pcie_get_io_base_address(0);
+               octeon_pcie1_controller.io_resource->end =
+                       octeon_pcie1_controller.io_resource->start +
+                       cvmx_pcie_get_io_size(1) - 1;
+               register_pci_controller(&octeon_pcie1_controller);
+       }
+       return 0;
+}
+
+arch_initcall(octeon_pcie_setup);
diff --git a/arch/mips/include/asm/octeon/cvmx-asm.h 
b/arch/mips/include/asm/octeon/cvmx-asm.h
index b21d3fc..093bcaf 100644
--- a/arch/mips/include/asm/octeon/cvmx-asm.h
+++ b/arch/mips/include/asm/octeon/cvmx-asm.h
@@ -119,7 +119,8 @@
        asm ("pop %[rd],%[rs]" : [rd] "=d" (result) : [rs] "d" (input))
 #define CVMX_DPOP(result, input) \
        asm ("dpop %[rd],%[rs]" : [rd] "=d" (result) : [rs] "d" (input))
-
+#define CVMX_CLZ(result, input) \
+       asm ("clz %[rd],%[rs]" : [rd] "=d" (result) : [rs] "d" (input))
 /* some new cop0-like stuff */
 #define CVMX_RDHWR(result, regstr) \
        asm volatile ("rdhwr %[rt],$" CVMX_TMP_STR(regstr) : [rt] "=d" (result))
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-errata.h 
b/arch/mips/include/asm/octeon/cvmx-helper-errata.h
new file mode 100644
index 0000000..ce5deea
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-errata.h
@@ -0,0 +1,92 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Fixes and workaround for Octeon chip errata. This file
+ * contains functions called by cvmx-helper to workaround known
+ * chip errata. For the most part, code doesn't need to call
+ * these functions directly.
+ *
+ */
+#ifndef __CVMX_HELPER_ERRATA_H__
+#define __CVMX_HELPER_ERRATA_H__
+
+
+#include "cvmx-wqe.h"
+
+/**
+ * @INTERNAL
+ * Function to adjust internal IPD pointer alignments
+ *
+ * Returns 0 on success
+ *         !0 on failure
+ */
+extern int __cvmx_helper_errata_fix_ipd_ptr_alignment(void);
+
+/**
+ * @INTERNAL
+ * Workaround ASX setup errata with CN38XX pass1
+ *
+ * @interface: Interface to setup
+ * @port:      Port to setup (0..3)
+ * @cpu_clock_hz:
+ *                  Chip frequency in Hertz
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_errata_asx_pass1(int interface, int port,
+                                         int cpu_clock_hz);
+
+/**
+ * This function needs to be called on all Octeon chips with
+ * errata PKI-100.
+ *
+ * The Size field is 8 too large in WQE and next pointers
+ *
+ *  The Size field generated by IPD is 8 larger than it should
+ *  be. The Size field is <55:40> of both:
+ *      - WORD3 in the work queue entry, and
+ *      - the next buffer pointer (which precedes the packet data
+ *        in each buffer).
+ *
+ * @work:   Work queue entry to fix
+ * Returns Zero on success. Negative on failure
+ */
+extern int cvmx_helper_fix_ipd_packet_chain(struct cvmx_wqe *work);
+
+/**
+ * Due to errata G-720, the 2nd order CDR circuit on CN52XX pass
+ * 1 doesn't work properly. The following code disables 2nd order
+ * CDR for the specified QLM.
+ *
+ * @qlm:    QLM to disable 2nd order CDR for.
+ */
+extern void __cvmx_helper_errata_qlm_disable_2nd_order_cdr(int qlm);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-util.h 
b/arch/mips/include/asm/octeon/cvmx-helper-util.h
new file mode 100644
index 0000000..d720217
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-util.h
@@ -0,0 +1,266 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Small helper utilities.
+ *
+ */
+
+#ifndef __CVMX_HELPER_UTIL_H__
+#define __CVMX_HELPER_UTIL_H__
+
+#ifdef CVMX_ENABLE_HELPER_FUNCTIONS
+
+/**
+ * Convert a interface mode into a human readable string
+ *
+ * @mode:   Mode to convert
+ *
+ * Returns String
+ */
+extern const char
+    *cvmx_helper_interface_mode_to_string(cvmx_helper_interface_mode_t mode);
+
+/**
+ * Debug routine to dump the packet structure to the console
+ *
+ * @work:   Work queue entry containing the packet to dump
+ * Returns
+ */
+extern int cvmx_helper_dump_packet(cvmx_wqe_t *work);
+
+/**
+ * Setup Random Early Drop on a specific input queue
+ *
+ * @queue:  Input queue to setup RED on (0-7)
+ * @pass_thresh:
+ *               Packets will begin slowly dropping when there are less than
+ *               this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *               All incomming packets will be dropped when there are less
+ *               than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+extern int cvmx_helper_setup_red_queue(int queue, int pass_thresh,
+                                      int drop_thresh);
+
+/**
+ * Setup Random Early Drop to automatically begin dropping packets.
+ *
+ * @pass_thresh:
+ *               Packets will begin slowly dropping when there are less than
+ *               this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *               All incomming packets will be dropped when there are less
+ *               than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+extern int cvmx_helper_setup_red(int pass_thresh, int drop_thresh);
+
+/**
+ * Get the version of the CVMX libraries.
+ *
+ * Returns Version string. Note this buffer is allocated statically
+ *         and will be shared by all callers.
+ */
+extern const char *cvmx_helper_get_version(void);
+
+/**
+ * @INTERNAL
+ * Setup the common GMX settings that determine the number of
+ * ports. These setting apply to almost all configurations of all
+ * chips.
+ *
+ * @interface: Interface to configure
+ * @num_ports: Number of ports on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_setup_gmx(int interface, int num_ports);
+
+/**
+ * Returns the IPD/PKO port number for a port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ * @port:      Port on the interface
+ *
+ * Returns IPD/PKO port number
+ */
+extern int cvmx_helper_get_ipd_port(int interface, int port);
+
+/**
+ * Returns the IPD/PKO port number for the first port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ *
+ * Returns IPD/PKO port number
+ */
+static inline int cvmx_helper_get_first_ipd_port(int interface)
+{
+       return cvmx_helper_get_ipd_port(interface, 0);
+}
+
+/**
+ * Returns the IPD/PKO port number for the last port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ *
+ * Returns IPD/PKO port number
+ */
+static inline int cvmx_helper_get_last_ipd_port(int interface)
+{
+       extern int cvmx_helper_ports_on_interface(int interface);
+
+       return cvmx_helper_get_first_ipd_port(interface) +
+               cvmx_helper_ports_on_interface(interface) - 1;
+}
+
+/**
+ * Free the packet buffers contained in a work queue entry.
+ * The work queue entry is not freed.
+ *
+ * @work:   Work queue entry with packet to free
+ */
+static inline void cvmx_helper_free_packet_data(cvmx_wqe_t *work)
+{
+       uint64_t number_buffers;
+       cvmx_buf_ptr_t buffer_ptr;
+       cvmx_buf_ptr_t next_buffer_ptr;
+       uint64_t start_of_buffer;
+
+       number_buffers = work->word2.s.bufs;
+       if (number_buffers == 0)
+               return;
+       buffer_ptr = work->packet_ptr;
+
+       /*
+        * Since the number of buffers is not zero, we know this is
+        * not a dynamic short packet. We need to check if it is a
+        * packet received with IPD_CTL_STATUS[NO_WPTR]. If this is
+        * true, we need to free all buffers except for the first
+        * one. The caller doesn't expect their WQE pointer to be
+        * freed.
+        */
+       start_of_buffer = ((buffer_ptr.s.addr >> 7) - buffer_ptr.s.back) << 7;
+       if (cvmx_ptr_to_phys(work) == start_of_buffer) {
+               next_buffer_ptr =
+                   *(cvmx_buf_ptr_t *) cvmx_phys_to_ptr(buffer_ptr.s.addr - 8);
+               buffer_ptr = next_buffer_ptr;
+               number_buffers--;
+       }
+
+       while (number_buffers--) {
+               /*
+                * Remember the back pointer is in cache lines, not
+                * 64bit words.
+                */
+               start_of_buffer =
+                   ((buffer_ptr.s.addr >> 7) - buffer_ptr.s.back) << 7;
+               /*
+                * Read pointer to next buffer before we free the
+                * current buffer.
+                */
+               next_buffer_ptr =
+                   *(cvmx_buf_ptr_t *) cvmx_phys_to_ptr(buffer_ptr.s.addr - 8);
+               cvmx_fpa_free(cvmx_phys_to_ptr(start_of_buffer),
+                             buffer_ptr.s.pool, 0);
+               buffer_ptr = next_buffer_ptr;
+       }
+}
+
+#endif /* CVMX_ENABLE_HELPER_FUNCTIONS */
+
+/**
+ * Returns the interface number for an IPD/PKO port number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface number
+ */
+extern int cvmx_helper_get_interface_num(int ipd_port);
+
+/**
+ * Returns the interface index number for an IPD/PKO port
+ * number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface index number
+ */
+extern int cvmx_helper_get_interface_index_num(int ipd_port);
+
+/**
+ * Initialize the internal QLM JTAG logic to allow programming
+ * of the JTAG chain by the cvmx_helper_qlm_jtag_*() functions.
+ * These functions should only be used at the direction of Cavium
+ * Networks. Programming incorrect values into the JTAG chain
+ * can cause chip damage.
+ */
+extern void cvmx_helper_qlm_jtag_init(void);
+
+/**
+ * Write up to 32bits into the QLM jtag chain. Bits are shifted
+ * into the MSB and out the LSB, so you should shift in the low
+ * order bits followed by the high order bits. The JTAG chain is
+ * 4 * 268 bits long, or 1072.
+ *
+ * @qlm:    QLM to shift value into
+ * @bits:   Number of bits to shift in (1-32).
+ * @data:   Data to shift in. Bit 0 enters the chain first, followed by
+ *               bit 1, etc.
+ *
+ * Returns The low order bits of the JTAG chain that shifted out of the
+ *         circle.
+ */
+extern uint32_t cvmx_helper_qlm_jtag_shift(int qlm, int bits, uint32_t data);
+
+/**
+ * Shift long sequences of zeros into the QLM JTAG chain. It is
+ * common to need to shift more than 32 bits of zeros into the
+ * chain. This function is a convience wrapper around
+ * cvmx_helper_qlm_jtag_shift() to shift more than 32 bits of
+ * zeros at a time.
+ *
+ * @qlm:    QLM to shift zeros into
+ * @bits:
+ */
+extern void cvmx_helper_qlm_jtag_shift_zeros(int qlm, int bits);
+
+/**
+ * Program the QLM JTAG chain into all lanes of the QLM. You must
+ * have already shifted in 268*4, or 1072 bits into the JTAG
+ * chain. Updating invalid values can possibly cause chip damage.
+ *
+ * @qlm:    QLM to program
+ */
+extern void cvmx_helper_qlm_jtag_update(int qlm);
+
+#endif /* __CVMX_HELPER_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-packet.h 
b/arch/mips/include/asm/octeon/cvmx-packet.h
index 38aefa1..1cb3419 100644
--- a/arch/mips/include/asm/octeon/cvmx-packet.h
+++ b/arch/mips/include/asm/octeon/cvmx-packet.h
@@ -25,7 +25,8 @@
  * Contact Cavium Networks for more information
  ***********************license end**************************************/
 
-/*
+/**
+ *
  * Packet buffer defines.
  */
 
@@ -39,18 +40,23 @@ union cvmx_buf_ptr {
        void *ptr;
        uint64_t u64;
        struct {
-               /* if set, invert the "free" pick of the overall
+               /*
+                * If set, invert the "free" pick of the overall
                 * packet. HW always sets this bit to 0 on inbound
-                * packet */
+                * packet.
+                */
                uint64_t i:1;
 
-               /* Indicates the amount to back up to get to the
+               /*
+                * Indicates the amount to back up to get to the
                 * buffer start in cache lines. In most cases this is
                 * less than one complete cache line, so the value is
-                * zero */
+                * zero.
+                */
                uint64_t back:4;
                /* The pool that the buffer came from / goes to */
                uint64_t pool:3;
+
                /* The size of the segment pointed to by addr (in bytes) */
                uint64_t size:16;
                /* Pointer to the first byte of the data, NOT buffer */
diff --git a/arch/mips/include/asm/octeon/cvmx-pcie.h 
b/arch/mips/include/asm/octeon/cvmx-pcie.h
new file mode 100644
index 0000000..55a5ac1
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pcie.h
@@ -0,0 +1,284 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Interface to PCIe as a host(RC) or target(EP)
+ *
+ */
+
+#ifndef __CVMX_PCIE_H__
+#define __CVMX_PCIE_H__
+
+union cvmx_pcie_address {
+       uint64_t u64;
+       struct {
+               uint64_t upper:2;       /* Normally 2 for XKPHYS */
+               uint64_t reserved_49_61:13;     /* Must be zero */
+               uint64_t io:1;  /* 1 for IO space access */
+               uint64_t did:5; /* PCIe DID = 3 */
+               uint64_t subdid:3;      /* PCIe SubDID = 1 */
+               uint64_t reserved_36_39:4;      /* Must be zero */
+               uint64_t es:2;  /* Endian swap = 1 */
+               uint64_t port:2;        /* PCIe port 0,1 */
+               uint64_t reserved_29_31:3;      /* Must be zero */
+               /*
+                * Selects the type of the configuration request (0 = type 0,
+                * 1 = type 1).
+                */
+               uint64_t ty:1;
+               /* Target bus number sent in the ID in the request. */
+               uint64_t bus:8;
+               /*
+                * Target device number sent in the ID in the
+                * request. Note that Dev must be zero for type 0
+                * configuration requests.
+                */
+               uint64_t dev:5;
+               /* Target function number sent in the ID in the request. */
+               uint64_t func:3;
+               /*
+                * Selects a register in the configuration space of
+                * the target.
+                */
+               uint64_t reg:12;
+       } config;
+       struct {
+               uint64_t upper:2;       /* Normally 2 for XKPHYS */
+               uint64_t reserved_49_61:13;     /* Must be zero */
+               uint64_t io:1;  /* 1 for IO space access */
+               uint64_t did:5; /* PCIe DID = 3 */
+               uint64_t subdid:3;      /* PCIe SubDID = 2 */
+               uint64_t reserved_36_39:4;      /* Must be zero */
+               uint64_t es:2;  /* Endian swap = 1 */
+               uint64_t port:2;        /* PCIe port 0,1 */
+               uint64_t address:32;    /* PCIe IO address */
+       } io;
+       struct {
+               uint64_t upper:2;       /* Normally 2 for XKPHYS */
+               uint64_t reserved_49_61:13;     /* Must be zero */
+               uint64_t io:1;  /* 1 for IO space access */
+               uint64_t did:5; /* PCIe DID = 3 */
+               uint64_t subdid:3;      /* PCIe SubDID = 3-6 */
+               uint64_t reserved_36_39:4;      /* Must be zero */
+               uint64_t address:36;    /* PCIe Mem address */
+       } mem;
+};
+
+/**
+ * Return the Core virtual base address for PCIe IO access. IOs are
+ * read/written as an offset from this address.
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns 64bit Octeon IO base address for read/write
+ */
+uint64_t cvmx_pcie_get_io_base_address(int pcie_port);
+
+/**
+ * Size of the IO address region returned at address
+ * cvmx_pcie_get_io_base_address()
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns Size of the IO window
+ */
+uint64_t cvmx_pcie_get_io_size(int pcie_port);
+
+/**
+ * Return the Core virtual base address for PCIe MEM access. Memory is
+ * read/written as an offset from this address.
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns 64bit Octeon IO base address for read/write
+ */
+uint64_t cvmx_pcie_get_mem_base_address(int pcie_port);
+
+/**
+ * Size of the Mem address region returned at address
+ * cvmx_pcie_get_mem_base_address()
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns Size of the Mem window
+ */
+uint64_t cvmx_pcie_get_mem_size(int pcie_port);
+
+/**
+ * Initialize a PCIe port for use in host(RC) mode. It doesn't
+ * enumerate the bus.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success
+ */
+int cvmx_pcie_rc_initialize(int pcie_port);
+
+/**
+ * Shutdown a PCIe port and put it in reset
+ *
+ * @pcie_port: PCIe port to shutdown
+ *
+ * Returns Zero on success
+ */
+int cvmx_pcie_rc_shutdown(int pcie_port);
+
+/**
+ * Read 8bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+uint8_t cvmx_pcie_config_read8(int pcie_port, int bus, int dev, int fn,
+                              int reg);
+
+/**
+ * Read 16bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+uint16_t cvmx_pcie_config_read16(int pcie_port, int bus, int dev, int fn,
+                                int reg);
+
+/**
+ * Read 32bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+uint32_t cvmx_pcie_config_read32(int pcie_port, int bus, int dev, int fn,
+                                int reg);
+
+/**
+ * Write 8bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+void cvmx_pcie_config_write8(int pcie_port, int bus, int dev, int fn, int reg,
+                            uint8_t val);
+
+/**
+ * Write 16bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+void cvmx_pcie_config_write16(int pcie_port, int bus, int dev, int fn, int reg,
+                             uint16_t val);
+
+/**
+ * Write 32bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:        Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+void cvmx_pcie_config_write32(int pcie_port, int bus, int dev, int fn, int reg,
+                             uint32_t val);
+
+/**
+ * Read a PCIe config space register indirectly. This is used for
+ * registers of the form PCIEEP_CFG??? and PCIERC?_CFG???.
+ *
+ * @pcie_port:  PCIe port to read from
+ * @cfg_offset: Address to read
+ *
+ * Returns Value read
+ */
+uint32_t cvmx_pcie_cfgx_read(int pcie_port, uint32_t cfg_offset);
+
+/**
+ * Write a PCIe config space register indirectly. This is used for
+ * registers of the form PCIEEP_CFG??? and PCIERC?_CFG???.
+ *
+ * @pcie_port:  PCIe port to write to
+ * @cfg_offset: Address to write
+ * @val:        Value to write
+ */
+void cvmx_pcie_cfgx_write(int pcie_port, uint32_t cfg_offset, uint32_t val);
+
+/**
+ * Write a 32bit value to the Octeon NPEI register space
+ *
+ * @address: Address to write to
+ * @val:     Value to write
+ */
+static inline void cvmx_pcie_npei_write32(uint64_t address, uint32_t val)
+{
+       cvmx_write64_uint32(address ^ 4, val);
+       cvmx_read64_uint32(address ^ 4);
+}
+
+/**
+ * Read a 32bit value from the Octeon NPEI register space
+ *
+ * @address: Address to read
+ * Returns The result
+ */
+static inline uint32_t cvmx_pcie_npei_read32(uint64_t address)
+{
+       return cvmx_read64_uint32(address ^ 4);
+}
+
+/**
+ * Initialize a PCIe port for use in target(EP) mode.
+ *
+ * Returns Zero on success
+ */
+int cvmx_pcie_ep_initialize(void);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-wqe.h 
b/arch/mips/include/asm/octeon/cvmx-wqe.h
new file mode 100644
index 0000000..fadc700
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-wqe.h
@@ -0,0 +1,422 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * This header file defines the work queue entry (wqe) data structure.
+ * Since this is a commonly used structure that depends on structures
+ * from several hardware blocks, those definitions have been placed
+ * in this file to create a single point of definition of the wqe
+ * format.
+ *
+ * Data structures are still named according to the block that they
+ * relate to.
+ *
+ */
+
+#ifndef __CVMX_WQE_H__
+#define __CVMX_WQE_H__
+
+#include "cvmx-packet.h"
+
+#define OCT_TAG_TYPE_STRING(x) (                                       \
+       {                                                               \
+               const char *r;                                          \
+               switch (x) {                                            \
+               case CVMX_POW_TAG_TYPE_ORDERED:                         \
+                       r = "ORDERED";                                  \
+                       break;                                          \
+               case CVMX_POW_TAG_TYPE_ATOMIC:                          \
+                       r = "ATOMIC";                                   \
+                       break;                                          \
+               case CVMX_POW_TAG_TYPE_NULL:                            \
+                       r = "NULL";                                     \
+                       break;                                          \
+               default:                                                \
+                       r = "NULL_NULL";                                \
+                       break;                                          \
+               }                                                       \
+               r;                                                      \
+       })
+
+/**
+ * HW decode / err_code in work queue entry
+ */
+union cvmx_pip_wqe_word2{
+       uint64_t u64;
+
+       /* Use this struct if the hardware determines that the packet is IP */
+       struct {
+               /* HW sets this to the number of buffers used by this packet */
+               uint64_t bufs:8;
+               /* HW sets to the number of L2 bytes prior to the IP */
+               uint64_t ip_offset:8;
+               /* Set to 1 if we found VLAN in the L2 */
+               uint64_t vlan_valid:1;
+               uint64_t unassigned:2;
+               /* HW sets to the VLAN CFI flag (valid when vlan_valid) */
+               uint64_t vlan_cfi:1;
+               /* HW sets to the VLAN_ID field (valid when vlan_valid) */
+               uint64_t vlan_id:12;
+
+               uint64_t unassigned2:12;
+               /* The packet needs to be decompressed */
+               uint64_t dec_ipcomp:1;
+               /* The packet is either TCP or UDP */
+               uint64_t tcp_or_udp:1;
+               /* The packet needs to be decrypted (ESP or AH) */
+               uint64_t dec_ipsec:1;
+               /* The packet is IPv6 */
+               uint64_t is_v6:1;
+
+               /*
+                * rcv_error, not_IP, IP_exc, is_frag, L4_error,
+                * software, etc.
+                */
+
+               /*
+                * Reserved for software use, hardware will clear on
+                * packet creation.
+                */
+               uint64_t software:1;
+               /* exceptional conditions below.  */
+
+               /*
+                * The receive interface hardware detected an L4 error
+                * (only applies if !is_frag) (only applies if
+                * !rcv_error && !not_IP && !IP_exc && !is_frag)
+                * failure indicated in err_code below, decode:
+                *
+                * - 1 = Malformed L4
+                *
+                * - 2 = L4 Checksum Error: the L4 checksum value is
+                *
+                * - 3 = UDP Length Error: The UDP length field would
+                *       make the UDP data longer than what remains in
+                *       the IP packet (as defined by the IP header
+                *       length field).
+                *
+                * - 4 = Bad L4 Port: either the source or destination
+                *       TCP/UDP port is 0.
+                *
+                * - 8 = TCP FIN Only: the packet is TCP and only the
+                *       FIN flag set.
+                *
+                * - 9 = TCP No Flags: the packet is TCP and no flags
+                *       are set.
+                *
+                * - 10 = TCP FIN RST: the packet is TCP and both FIN
+                *        and RST are set.
+                *
+                * - 11 = TCP SYN URG: the packet is TCP and both SYN
+                *        and URG are set.
+                *
+                * - 12 = TCP SYN RST: the packet is TCP and both SYN
+                *        and RST are set.
+                *
+                * - 13 = TCP SYN FIN: the packet is TCP and both SYN
+                *        and FIN are set.
+                *
+                */
+               uint64_t L4_error:1;
+               /* Set if the packet is a fragment */
+               uint64_t is_frag:1;
+
+               /*
+                * The receive interface hardware detected an IP error
+                * / exception (only applies if !rcv_error && !not_IP)
+                * failure indicated in err_code below, decode:
+                *
+                * - 1 = Not IP: the IP version field is neither 4 nor
+                *       6.
+                *
+                * - 2 = IPv4 Header Checksum Error: the IPv4 header
+                *       has a checksum violation.
+                *
+                * - 3 = IP Malformed Header: the packet is not long
+                *       enough to contain the IP header.
+                *
+                * - 4 = IP Malformed: the packet is not long enough
+                *       to contain the bytes indicated by the IP
+                *       header. Pad is allowed.
+                *
+                * - 5 = IP TTL Hop: the IPv4 TTL field or the IPv6
+                *       Hop Count field are zero.
+                *
+                * - 6 = IP Options.
+                */
+               uint64_t IP_exc:1;
+               /*
+                * Set if the hardware determined that the packet is a
+                * broadcast.
+                */
+               uint64_t is_bcast:1;
+               /*
+                * Set if the hardware determined that the packet is a
+                * multi-cast.
+                */
+               uint64_t is_mcast:1;
+               /*
+                * Set if the packet may not be IP (must be zero in
+                * this case).
+                */
+               uint64_t not_IP:1;
+               /*
+                * The receive interface hardware detected a receive
+                * error (must be zero in this case)
+                *
+                * lower err_code = first-level descriptor of the work
+                *
+                * zero for packet submitted by hardware that isn't on
+                * the slow path.
+                */
+               uint64_t rcv_error:1;
+
+               /* Type is cvmx_pip_err_t */
+               uint64_t err_code:8;
+       } s;
+
+       /* Use this to get at the 16 vlan bits */
+       struct {
+               uint64_t unused1:16;
+               uint64_t vlan:16;
+               uint64_t unused2:32;
+       } svlan;
+
+       /*
+        * Use this struct if the hardware could not determine that
+        * the packet is ip.
+        */
+       struct {
+               /* HW sets this to the number of buffers used by this packet. */
+               uint64_t bufs:8;
+               uint64_t unused:8;
+               /* Set to 1 if we found VLAN in the L2. */
+               uint64_t vlan_valid:1;
+               uint64_t unassigned:2;
+               /* HW sets to the VLAN CFI flag (valid when vlan_valid). */
+               uint64_t vlan_cfi:1;
+               /* HW sets to the VLAN_ID field (valid when vlan_valid). */
+               uint64_t vlan_id:12;
+
+               uint64_t unassigned2:16;
+               /*
+                * Reserved for software use, hardware will clear on
+                * packet creation.
+                */
+               uint64_t software:1;
+               uint64_t unassigned3:1;
+               /* Set if the hardware determined that the packet is rarp. */
+               uint64_t is_rarp:1;
+               /* Set if the hardware determined that the packet is arp. */
+               uint64_t is_arp:1;
+               /*
+                * Set if the hardware determined that the packet is a
+                * broadcast.
+                */
+               uint64_t is_bcast:1;
+               /*
+                * Set if the hardware determined that the packet is a
+                * multi-cast.
+                */
+               uint64_t is_mcast:1;
+               /*
+                * Set if the packet may not be IP (must be one in
+                * this case).
+                */
+               uint64_t not_IP:1;
+               /*
+                * The receive interface hardware detected a receive
+                * error. Failure indicated in err_code below, decode:
+                *
+                * - 1 = partial error: a packet was partially
+                *       received, but internal buffering / bandwidth
+                *       was not adequate to receive the entire
+                *       packet.
+                *
+                * - 2 = jabber error: the RGMII packet was too large
+                *       and is truncated.
+                *
+                * - 3 = overrun error: the RGMII packet is longer
+                *       than allowed and had an FCS error.
+                *
+                * - 4 = oversize error: the RGMII packet is longer
+                *       than allowed.
+                *
+                * - 5 = alignment error: the RGMII packet is not an
+                *       integer number of bytes and had an FCS error
+                *       (100M and 10M only).
+                *
+                * - 6 = fragment error: the RGMII packet is shorter
+                *       than allowed and had an FCS error.
+                *
+                * - 7 = GMX FCS error: the RGMII packet had an FCS
+                *       error.
+                *
+                * - 8 = undersize error: the RGMII packet is shorter
+                *       than allowed.
+                *
+                * - 9 = extend error: the RGMII packet had an extend
+                *       error.
+                *
+                * - 10 = length mismatch error: the RGMII packet had
+                *        a length that did not match the length field
+                *        in the L2 HDR.
+                *
+                * - 11 = RGMII RX error/SPI4 DIP4 Error: the RGMII
+                *        packet had one or more data reception errors
+                *        (RXERR) or the SPI4 packet had one or more
+                *        DIP4 errors.
+                *
+                * - 12 = RGMII skip error/SPI4 Abort Error: the RGMII
+                *        packet was not large enough to cover the
+                *        skipped bytes or the SPI4 packet was
+                *        terminated with an About EOPS.
+                *
+                * - 13 = RGMII nibble error/SPI4 Port NXA Error: the
+                *        RGMII packet had a studder error (data not
+                *        repeated - 10/100M only) or the SPI4 packet
+                *        was sent to an NXA.
+                *
+                * - 16 = FCS error: a SPI4.2 packet had an FCS error.
+                *
+                * - 17 = Skip error: a packet was not large enough to
+                *        cover the skipped bytes.
+                *
+                * - 18 = L2 header malformed: the packet is not long
+                *        enough to contain the L2
+                */
+
+               /*
+                * lower err_code = first-level descriptor of the
+                * work.
+                *
+                * zero for packet submitted by hardware that isn't on
+                * the slow path.
+                */
+               uint64_t rcv_error:1;
+
+               /* Type is cvmx_pip_err_t (union, so can't use directly. */
+               uint64_t err_code:8;
+       } snoip;
+
+};
+
+/**
+ * Work queue entry format
+ *
+ * must be 8-byte aligned
+ */
+struct cvmx_wqe {
+
+    /*****************************************************************
+     * WORD 0
+     *  HW WRITE: the following 64 bits are filled by HW when a packet arrives
+     */
+
+    /**
+     * raw chksum result generated by the HW
+     */
+       uint16_t hw_chksum;
+    /**
+     * Field unused by hardware - available for software
+     */
+       uint8_t unused;
+    /**
+     * Next pointer used by hardware for list maintenance.
+     * May be written/read by HW before the work queue
+     *           entry is scheduled to a PP
+     * (Only 36 bits used in Octeon 1)
+     */
+       uint64_t next_ptr:40;
+
+    /*****************************************************************
+     * WORD 1
+     *  HW WRITE: the following 64 bits are filled by HW when a packet arrives
+     */
+
+    /**
+     * HW sets to the total number of bytes in the packet
+     */
+       uint64_t len:16;
+    /**
+     * HW sets this to input physical port
+     */
+       uint64_t ipprt:6;
+
+    /**
+     * HW sets this to what it thought the priority of the input packet was
+     */
+       uint64_t qos:3;
+
+    /**
+     * the group that the work queue entry will be scheduled to
+     */
+       uint64_t grp:4;
+    /**
+     * the type of the tag (ORDERED, ATOMIC, NULL)
+     */
+       uint64_t tag_type:3;
+    /**
+     * the synchronization/ordering tag
+     */
+       uint64_t tag:32;
+
+    /**
+     * WORD 2 HW WRITE: the following 64-bits are filled in by
+     *   hardware when a packet arrives This indicates a variety of
+     *   status and error conditions.
+     */
+       union cvmx_pip_wqe_word2 word2;
+
+    /**
+     * Pointer to the first segment of the packet.
+     */
+       union cvmx_buf_ptr packet_ptr;
+
+    /**
+     *   HW WRITE: octeon will fill in a programmable amount from the
+     *             packet, up to (at most, but perhaps less) the amount
+     *             needed to fill the work queue entry to 128 bytes
+     *   If the packet is recognized to be IP, the hardware starts (except that
+     *   the IPv4 header is padded for appropriate alignment) writing here 
where
+     *   the IP header starts.
+     *   If the packet is not recognized to be IP, the hardware starts writing
+     *   the beginning of the packet here.
+     */
+       uint8_t packet_data[96];
+
+    /**
+     * If desired, SW can make the work Q entry any length. For the
+     * purposes of discussion here, Assume 128B always, as this is all that
+     * the hardware deals with.
+     *
+     */
+
+} CVMX_CACHE_LINE_ALIGNED;
+
+#endif /* __CVMX_WQE_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx.h 
b/arch/mips/include/asm/octeon/cvmx.h
index 03fddfa..e31e3fe 100644
--- a/arch/mips/include/asm/octeon/cvmx.h
+++ b/arch/mips/include/asm/octeon/cvmx.h
@@ -376,6 +376,18 @@ static inline uint64_t cvmx_get_cycle(void)
 }
 
 /**
+ * Wait for the specified number of cycle
+ *
+ */
+static inline void cvmx_wait(uint64_t cycles)
+{
+       uint64_t done = cvmx_get_cycle() + cycles;
+
+       while (cvmx_get_cycle() < done)
+               ; /* Spin */
+}
+
+/**
  * Reads a chip global cycle counter.  This counts CPU cycles since
  * chip reset.  The counter is 64 bit.
  * This register does not exist on CN38XX pass 1 silicion
diff --git a/arch/mips/include/asm/octeon/octeon.h 
b/arch/mips/include/asm/octeon/octeon.h
index edc6760..cac9b1a 100644
--- a/arch/mips/include/asm/octeon/octeon.h
+++ b/arch/mips/include/asm/octeon/octeon.h
@@ -245,4 +245,6 @@ static inline uint32_t octeon_npi_read32(uint64_t address)
        return cvmx_read64_uint32(address ^ 4);
 }
 
+extern struct cvmx_bootinfo *octeon_bootinfo;
+
 #endif /* __ASM_OCTEON_OCTEON_H */
-- 
1.5.6.5


<Prev in Thread] Current Thread [Next in Thread>