linux-mips
[Top] [All Lists]

[PATCH] Kill CONFIG_TX4927BUG_WORKAROUND

To: linux-mips@linux-mips.org
Subject: [PATCH] Kill CONFIG_TX4927BUG_WORKAROUND
From: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Date: Fri, 13 Jul 2007 02:00:26 +0900 (JST)
Cc: ralf@linux-mips.org, sshtylyov@ru.mvista.com, rpjday@mindspring.com
Original-recipient: rfc822;linux-mips@linux-mips.org
Sender: linux-mips-bounce@linux-mips.org
Kill workarounds for very early chip (perhaps pre-TX4927A).

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
---
diff --git a/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_setup.c 
b/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_setup.c
index 08e53cc..ab72292 100644
--- a/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_setup.c
+++ b/arch/mips/tx4927/toshiba_rbtx4927/toshiba_rbtx4927_setup.c
@@ -138,7 +138,6 @@ extern void toshiba_rbtx4927_irq_setup(void);
 char *prom_getcmdline(void);
 
 #ifdef CONFIG_PCI
-#define CONFIG_TX4927BUG_WORKAROUND
 #undef TX4927_SUPPORT_COMMAND_IO
 #undef  TX4927_SUPPORT_PCI_66
 int tx4927_cpu_clock = 100000000;      /* 100MHz */
@@ -669,15 +668,7 @@ void tx4927_pci_setup(void)
 
        /* PCI->GB mappings (MEM 16MB) -not used */
        tx4927_pcicptr->p2gm1plbase = 0xffffffff;
-#ifdef CONFIG_TX4927BUG_WORKAROUND
-       /*
-        * TX4927-PCIC-BUG: P2GM1PUBASE must be 0
-        * if P2GM0PUBASE was 0.
-        */
-       tx4927_pcicptr->p2gm1pubase = 0;
-#else
        tx4927_pcicptr->p2gm1pubase = 0xffffffff;
-#endif
        tx4927_pcicptr->p2gmgbase[1] = 0;
 
        /* PCI->GB mappings (MEM 1MB) -not used */
@@ -910,16 +901,6 @@ void __init toshiba_rbtx4927_setup(void)
        if (tx4927_ccfg_toeon)
                tx4927_ccfgptr->ccfg |= TX4927_CCFG_TOE;
 
-       /* SDRAMC fixup */
-#ifdef CONFIG_TX4927BUG_WORKAROUND
-       /*
-        * TX4927-BUG: INF 01-01-18/ BUG 01-01-22
-        * G-bus timeout error detection is incorrect
-        */
-       if (tx4927_ccfg_toeon)
-               tx4927_sdramcptr->tr |= 0x02000000;     /* RCD:3tck */
-#endif
-
        tx4927_pci_setup();
        if (tx4927_using_backplane == 1)
                printk("backplane board IS installed\n");

<Prev in Thread] Current Thread [Next in Thread>