linux-mips
[Top] [All Lists]

Re: Crosstools for MALTA MIPS in little endian

To: "Ralf Baechle" <ralf@linux-mips.org>, "Nigel Stephens" <nigel@mips.com>
Subject: Re: Crosstools for MALTA MIPS in little endian
From: "Shyamal Sadanshio" <shyamal.sadanshio@gmail.com>
Date: Thu, 27 Apr 2006 12:09:46 +0530
Cc: linux-mips@linux-mips.org
Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=beta; d=gmail.com; h=received:message-id:date:from:to:subject:cc:in-reply-to:mime-version:content-type:references; b=dF1j1aCztjSJqyPUc4+NRlNMipQEH0i5aKhkxavS8aKYkfk3WF9aPyCya/atuCk7l7eQSdMlTQ0ilS2D3GlcKWck3+IXyyeOYkMvsp0ZuH3rbNoKkD/RqbXz2k1qy5FJCdglLosgpVOrCQqCXV16idMjvamb2xwaVM+y/kv7RJ0=
In-reply-to: <20060426221254.GA21670@linux-mips.org>
Original-recipient: rfc822;linux-mips@linux-mips.org
References: <3857255c0604210808y1208045by3449b003b4b2ffea@mail.gmail.com> <4448F638.9060502@mips.com> <3857255c0604260145i65356e12w89c6667756cddd3c@mail.gmail.com> <20060426221254.GA21670@linux-mips.org>
Sender: linux-mips-bounce@linux-mips.org
Hi Nigel, Ralf,

Yes, I'm using the default config with option set to R1 processor.
I am using NFS filesystem and loading the image through ethernet using minicom.

Here's the sequence:
  Start NFS service
  load tftp://192.168.2.237/vmlinux.srec
  go .nfsroot=192.168.2.237/linux/mipsel ip=192.168.2.24

Here's the YAMON boot message:
NUX started...
Config serial console: console=ttyS0,38400n8r

* Exception (user) : Breakpoint *
CAUSE    = 0x10808024  STATUS   = 0x10002c02
CONFIG   = 0x80030083  CONFIG1  = 0x1e9b4d8a
EPC      = 0x80549830  ERROREPC = 0x80029cf4
BADVADDR = 0xffffffff  HI       = 0x00000000
LO       = 0x04000000

$ 0(zr):0x00000000  $ 8(t0):0x804c18dc  $16(s0):0x8056d0b8  $24(t8):0x804bfddd
$ 1(at):0x10002c00  $ 9(t1):0x0000007f  $17(s1):0x80490000  $25(t9):0x80571f77
$ 2(v0):0xffffffff  $10(t2):0x00000040  $18(s2):0x80570000  $26(k0):0x00000000
$ 3(v1):0xffffffe1  $11(t3):0x80570000  $19(s3):0x8056d0bc  $27(k1):0x00000000
$ 4(a0):0x00000040  $12(t4):0x80570000  $20(s4):0x00000000  $28(gp):0x804be000
$ 5(a1):0x00000000  $13(t5):0x00000000  $21(s5):0x804bffc0  $29(sp):0x804bff50
$ 6(a2):0x08000000  $14(t6):0x80571b91  $22(s6):0x00000000  $30(s8):0x8009e0c0
$ 7(a3):0xbbe00000  $15(t7):0x00000010  $23(s7):0x00000000  $31(ra):0x8054b22c

I have attached my config file along with this mail.

Thanks and Regards,
Shyamal


On 4/27/06, Ralf Baechle <ralf@linux-mips.org> wrote:
> On Wed, Apr 26, 2006 at 02:15:29PM +0530, Shyamal Sadanshio wrote:
>
> > I am facing boot problem with the Malta specific 2.6.12-rc6 kernel.
> > The kernel is not booting up on our Malta 4kc development board.
> > I do not see any error messages on the minicom window.
>
> In case you're using the default configuration file, it's set to
> MIPS32R1 but the 4Kc is an R1 processor.  Are you sure you really have a
> 4Kc and not a 4Kec?  The latter is an R2 processor.
>
>   Ralf
>

Attachment: config1.txt
Description: Text document

<Prev in Thread] Current Thread [Next in Thread>