linux-mips
[Top] [All Lists]

Re: USB on AU1550

To: Jay Monkman <jtm@smoothsmoothie.com>
Subject: Re: USB on AU1550
From: Matej Kupljen <matej.kupljen@ultra.si>
Date: Thu, 29 Sep 2005 11:07:11 +0200
Cc: linux-mips@linux-mips.org
In-reply-to: <433B0299.8080507@smoothsmoothie.com>
Original-recipient: rfc822;linux-mips@linux-mips.org
References: <433B0299.8080507@smoothsmoothie.com>
Sender: linux-mips-bounce@linux-mips.org
Hi

> I'm trying to get USB working on my AU1550 board, and I'm getting an error I
> don't understand. I've searched the web and the mailing list archives, but
> haven't found anything relevant.

Not the answer to you question, but I have some problems with USB on
AU1200 board too. I use AirStar2 USB card (this is DVB-T card) and it
is recognized by AU1200 and can communicate with it. I can tune to 
transporder, but the data (transport stream) is not send from the
USB card. 
The card conforms to USB 1.1. 
I tried it on a PC running Linux and it works fine.

AU1200 kernel: 2.6.11, PC kernel: 2.6.13.2.

Any thoughts?

BR,
Matej

P.S.: This is the log:
----------------------------------------------------------------------------------
flexcop_usb: running at FULL speed.
DVB: registering new adapter (FlexCop Digital TV device).
f010
b2c2-flexcop: MAC address = <DELETED>
b2c2-flexcop: found the mt352 at i2c address: 0x0f
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'USB'
bus controlled by a 'FlexCopIII' complete
creating 4 iso-urbs with 4 frames each of 1023 bytes size = 16368.
initializing and submitting urb no. 0 (buf_offset: 0).
urb no: 0, frame: 0, frame_offset: 0
urb no: 0, frame: 1, frame_offset: 1023
urb no: 0, frame: 2, frame_offset: 2046
urb no: 0, frame: 3, frame_offset: 3069
submitted urb no. 0.
initializing and submitting urb no. 1 (buf_offset: 4092).
urb no: 1, frame: 0, frame_offset: 0
urb no: 1, frame: 1, frame_offset: 1023
urb no: 1, frame: 2, frame_offset: 2046
urb no: 1, frame: 3, frame_offset: 3069
submitted urb no. 1.
initializing and submitting urb no. 2 (buf_offset: 8184).
urb no: 2, frame: 0, frame_offset: 0
urb no: 2, frame: 1, frame_offset: 1023
urb no: 2, frame: 2, frame_offset: 2046
urb no: 2, frame: 3, frame_offset: 3069
submitted urb no. 2.
initializing and submitting urb no. 3 (buf_offset: 12276).
urb no: 3, frame: 0, frame_offset: 0
urb no: 3, frame: 1, frame_offset: 1023
urb no: 3, frame: 2, frame_offset: 2046
urb no: 3, frame: 3, frame_offset: 3069
submitted urb no. 3.
flexcop_usb: Technisat/B2C2 FlexCop II/IIb/III Digital TV USB Driver
successfully initialized and connected.
usbcore: registered new driver b2c2_flexcop_usb
----------------------------------------------------------------------------------


<Prev in Thread] Current Thread [Next in Thread>
  • USB on AU1550, Jay Monkman
    • Re: USB on AU1550, Matej Kupljen <=