Hi there ...
My name is Thomas I'm trying to use an USB-headset on a meshcube, a MIPS
based embedded device (http://meshcube.org/meshwiki/). If I plug in the
headset while running 2.4.27 a led on the headset turns on. If I do the
same with 2.6.12-rc6 (latest MIPS CVS) nothing happens. I also tried an
optical USB-mouse with the same result. All these tests are done with
Debian GNU/Linux Sarge 3.1 on NFS-root.
My kernelconfig is:
$ sed '/^#/d;/USB/!d' .config
CONFIG_SND_USB_AUDIO=m
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_EHCI_HCD=m
CONFIG_USB_OHCI_HCD=y
CONFIG_USB_HID=y
CONFIG_USB_HIDINPUT=y
kernel boot messages are:
usbcore: registered new driver usbfs
usbcore: registered new driver hub
[...]
au1xxx-ohci au1xxx-ohci.0: Au1xxx OHCI
au1xxx-ohci au1xxx-ohci.0: new USB bus registered, assigned bus number 1
au1xxx-ohci au1xxx-ohci.0: irq 26, io mem 0x10100000
usb usb1: Product: Au1xxx OHCI
usb usb1: Manufacturer: Linux 2.6.12-rc6 ohci_hcd
usb usb1: SerialNumber: Au1xxx
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v2.2
sl811: driver sl811-hcd, 19 May 2005
FYI 2.4.27 messages:
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xb0100000, IRQ 26
host/usb-ohci.c: usb-builtin, non-PCI OHCI
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
hotplug (initscripts) report:
Starting hotplug subsystem:
pci
pci [success]
usb
usb [success]
isapnp
isapnp [success]
ide
ide [success]
input
input [success]
scsi
scsi [success]
done.
the proc-filesystem tells:
$ cat /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.11 ohci_hcd
S: Product=Au1xxx OHCI
S: SerialNumber=au1xxx
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
As far as I can see USB drivers are working correctly, hardware is
detected but the USB is not working. Any hints?
TIA
Thomas
--
Please keep mailinglists in english as they are meant to be
read in the whole world. -- Feel free to send PM in german.
|