linux-mips
[Top] [All Lists]

[patch] repair failed merges of 2.6.12 in au1000_eth.c

To: linux-mips@linux-mips.org
Subject: [patch] repair failed merges of 2.6.12 in au1000_eth.c
From: Ulrich Eckhardt <eckhardt@satorlaser.com>
Date: Tue, 22 Mar 2005 14:04:39 +0100
Cc: ralf@linux-mips.org
Organization: Sator Laser GmbH
Original-recipient: rfc822;linux-mips@linux-mips.org
Sender: linux-mips-bounce@linux-mips.org
User-agent: KMail/1.7.1
Hi!

Seems a few things went wrong merging 2.6.12 into the l-m.o CVS, leading to 
code duplication. The compiler complains about an unbalanced #ifdef.

Uli

Changes:
 * repair wrong merges of changes from 2.6.12
 * remove an unused variable an an unnecessary set of brackets

---
Index: drivers/net/au1000_eth.c
===================================================================
RCS file: /home/cvs/linux/drivers/net/au1000_eth.c,v
retrieving revision 1.43
diff -u -w -r1.43 au1000_eth.c
--- drivers/net/au1000_eth.c 18 Mar 2005 17:37:32 -0000 1.43
+++ drivers/net/au1000_eth.c 22 Mar 2005 11:56:10 -0000
@@ -990,67 +990,7 @@
     the stub will be found as well as the actual PHY. However,
     the last found PHY will be used... usually at Addr 31 (Db1500). 
  */
- if ( (!phy_found) )
- {
-  u16 phy_id0, phy_id1;
-  int i;
-
-  phy_id0 = 0x1234;
-  phy_id1 = 0x5678;
-
-  /* search our mii table for the current mii */ 
-  for (i = 0; mii_chip_table[i].phy_id1; i++) {
-   if (phy_id0 == mii_chip_table[i].phy_id0 &&
-       phy_id1 == mii_chip_table[i].phy_id1) {
-    struct mii_phy * mii_phy = aup->mii;
-
-    printk(KERN_INFO "%s: %s at phy address %d\n",
-           dev->name, mii_chip_table[i].name, 
-           phy_addr);
-#ifdef CONFIG_MIPS_BOSPORUS
-    phy_found = 1;
-#endif
-    mii_phy->chip_info = mii_chip_table+i;
-    aup->phy_addr = phy_addr;
-    aup->want_autoneg = 1;
-    aup->phy_ops = mii_chip_table[i].phy_ops;
-    aup->phy_ops->phy_init(dev,phy_addr);
-
-    // Check for dual-phy and then store required 
-    // values and set indicators. We need to do 
-    // this now since mdio_{read,write} need the 
-    // control and data register addresses.
-    #ifdef CONFIG_BCM5222_DUAL_PHY
-    if ( mii_chip_table[i].dual_phy) {
-
-     /* assume both phys are controlled 
-      * through MAC0. Board specific? */
-     
-     /* sanity check */
-     if (!au_macs[0] || !au_macs[0]->mii)
-      return -1;
-     aup->mii->mii_control_reg = (u32 *)
-      &au_macs[0]->mac->mii_control;
-     aup->mii->mii_data_reg = (u32 *)
-      &au_macs[0]->mac->mii_data;
-    }
-    #endif
-    goto found;
-   }
-  }
- }
-found:
-
-#ifdef CONFIG_MIPS_BOSPORUS
- /* This is a workaround for the Micrel/Kendin 5 port switch
-    The second MAC doesn't see a PHY connected... so we need to
-    trick it into thinking we have one.
-  
-    If this kernel is run on another Au1500 development board
-    the stub will be found as well as the actual PHY. However,
-    the last found PHY will be used... usually at Addr 31 (Db1500). 
- */
- if ( (!phy_found) )
+ if ( !phy_found)
  {
   u16 phy_id0, phy_id1;
   int i;
@@ -1841,7 +1781,6 @@
 
 static int au1000_close(struct net_device *dev)
 {
- int i;
  u32 flags;
  struct au1000_private *aup = (struct au1000_private *) dev->priv;
 
@@ -2159,23 +2098,6 @@
     return crc;
 }
 
-
-static unsigned const ethernet_polynomial = 0x04c11db7U;
-static inline u32 ether_crc(int length, unsigned char *data)
-{
-    int crc = -1;
-
-    while(--length >= 0) {
-  unsigned char current_octet = *data++;
-  int bit;
-  for (bit = 0; bit < 8; bit++, current_octet >>= 1)
-   crc = (crc << 1) ^
-    ((crc < 0) ^ (current_octet & 1) ? 
-     ethernet_polynomial : 0);
-    }
-    return crc;
-}
-
 static void set_rx_mode(struct net_device *dev)
 {
  struct au1000_private *aup = (struct au1000_private *) dev->priv;

<Prev in Thread] Current Thread [Next in Thread>
  • [patch] repair failed merges of 2.6.12 in au1000_eth.c, Ulrich Eckhardt <=