linux-mips
[Top] [All Lists]

[PATCH] serial support for yosemite

To: linux-mips@linux-mips.org
Subject: [PATCH] serial support for yosemite
From: Thomas Koeller <thomas.koeller@baslerweb.com>
Date: Wed, 11 Aug 2004 11:28:44 +0200
Organization: Basler AG
Original-recipient: rfc822;linux-mips@linux-mips.org
Sender: linux-mips-bounce@linux-mips.org
User-agent: KMail/1.6.2
Hi,

this is a revised version of my previous yosemite patch.
It adds fully interrrupt-driven operation for both
serial ports as well as working kgdb support. It also
updates yosemite_defconfig to reflect the code changes.

tk




diff -rpu linux-mips/arch/mips/pmc-sierra/yosemite/dbg_io.c 
linux-mips-work/arch/mips/pmc-sierra/yosemite/dbg_io.c
--- linux-mips/arch/mips/pmc-sierra/yosemite/dbg_io.c   2004-05-20 
17:01:41.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/dbg_io.c      2004-08-10 
11:14:44.000000000 +0200
@@ -23,18 +23,22 @@
  *  675 Mass Ave, Cambridge, MA 02139, USA.
  */
 
-/*
- * Support for KGDB for the Yosemite board. We make use of single serial
- * port to be used for KGDB as well as console. The second serial port
- * seems to be having a problem. Single IRQ is allocated for both the
- * ports. Hence, the interrupt routing code needs to figure out whether
- * the interrupt came from channel A or B.
- */
-
 #include <linux/config.h>
+#include <asm/io.h>
+
+#include "setup.h"
 
 #if defined(CONFIG_KGDB)
-#include <asm/serial.h>
+
+#if defined(CONFIG_SERIAL_8250) && CONFIG_SERIAL_8250_NR_UARTS > 1
+#error Debug port used by serial driver
+#endif
+
+#define TITAN_UART_CLK         3686400
+#define TITAN_SERIAL_BASE_BAUD (TITAN_UART_CLK / 16)
+#define TITAN_SERIAL_BASE_0    0xfd000008UL
+#define TITAN_SERIAL_BASE_1    0xfd000000UL
+
 
 /*
  * Baud rate, Parity, Data and Stop bit settings for the
@@ -71,6 +75,7 @@
 #define        SERIAL_SEND_BUFFER      0x0
 #define        SERIAL_INTR_ENABLE      (1 * SERIAL_REG_OFS)
 #define        SERIAL_INTR_ID          (2 * SERIAL_REG_OFS)
+#define        SERIAL_FIFO_CONTROL     SERIAL_INTR_ID
 #define        SERIAL_DATA_FORMAT      (3 * SERIAL_REG_OFS)
 #define        SERIAL_LINE_CONTROL     (3 * SERIAL_REG_OFS)
 #define        SERIAL_MODEM_CONTROL    (4 * SERIAL_REG_OFS)
@@ -84,59 +89,26 @@
 #define        SERIAL_DIVISOR_MSB      (1 * SERIAL_REG_OFS)
 
 /*
- * Functions to READ and WRITE to serial port 0
+ * Functions to READ and WRITE to serial port
  */
-#define        SERIAL_READ(ofs)                (*((volatile unsigned char*)    
\
-                                       (TITAN_SERIAL_BASE + ofs)))
-
-#define        SERIAL_WRITE(ofs, val)          ((*((volatile unsigned char*)   
\
-                                       (TITAN_SERIAL_BASE + ofs))) = val)
+#define        SERIAL_READ(ofs)                readb(serbase + ofs)
+#define        SERIAL_WRITE(ofs, val)          writeb((val), serbase + ofs)
 
-/*
- * Functions to READ and WRITE to serial port 1
- */
-#define        SERIAL_READ_1(ofs)              (*((volatile unsigned char*)    
\
-                                       (TITAN_SERIAL_BASE_1 + ofs)
-
-#define        SERIAL_WRITE_1(ofs, val)        ((*((volatile unsigned char*)   
\
-                                       (TITAN_SERIAL_BASE_1 + ofs))) = val)
-
-/*
- * Second serial port initialization
- */
-void init_second_port(void)
-{
-       /* Disable Interrupts */
-       SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
-       SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0x0);
-
-       {
-               unsigned int divisor;
-
-               SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x80);
-               divisor = TITAN_SERIAL_BASE_BAUD / YOSEMITE_BAUD_115200;
-               SERIAL_WRITE_1(SERIAL_DIVISOR_LSB, divisor & 0xff);
-
-               SERIAL_WRITE_1(SERIAL_DIVISOR_MSB,
-                              (divisor & 0xff00) >> 8);
-               SERIAL_WRITE_1(SERIAL_LINE_CONTROL, 0x0);
-       }
-
-       SERIAL_WRITE_1(SERIAL_DATA_FORMAT, YOSEMITE_DATA_8BIT |
-                      YOSEMITE_PARITY_NONE | YOSEMITE_STOP_1BIT);
-
-       /* Enable Interrupts */
-       SERIAL_WRITE_1(SERIAL_INTR_ENABLE, 0xf);
-}
+static int initialized = 0;
 
 /* Initialize the serial port for KGDB debugging */
 void debugInit(unsigned int baud, unsigned char data, unsigned char parity,
-              unsigned char stop)
+       unsigned char stop)
 {
+       initialized = 1;
+       
        /* Disable Interrupts */
        SERIAL_WRITE(SERIAL_LINE_CONTROL, 0x0);
        SERIAL_WRITE(SERIAL_INTR_ENABLE, 0x0);
 
+       /* Disable FIFOs */
+       SERIAL_WRITE(SERIAL_FIFO_CONTROL, 0x00);
+
        {
                unsigned int divisor;
 
@@ -152,15 +124,11 @@ void debugInit(unsigned int baud, unsign
        SERIAL_WRITE(SERIAL_DATA_FORMAT, data | parity | stop);
 }
 
-static int remoteDebugInitialized = 0;
-
 unsigned char getDebugChar(void)
 {
-       if (!remoteDebugInitialized) {
-               remoteDebugInitialized = 1;
+       if (!initialized) {
                debugInit(YOSEMITE_BAUD_115200,
-                         YOSEMITE_DATA_8BIT,
-                         YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
+                         YOSEMITE_DATA_8BIT, YOSEMITE_PARITY_NONE, 
YOSEMITE_STOP_1BIT);
        }
 
        while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x1) == 0);
@@ -169,11 +137,9 @@ unsigned char getDebugChar(void)
 
 int putDebugChar(unsigned char byte)
 {
-       if (!remoteDebugInitialized) {
-               remoteDebugInitialized = 1;
+       if (!initialized) {
                debugInit(YOSEMITE_BAUD_115200,
-                         YOSEMITE_DATA_8BIT,
-                         YOSEMITE_PARITY_NONE, YOSEMITE_STOP_1BIT);
+                         YOSEMITE_DATA_8BIT, YOSEMITE_PARITY_NONE, 
YOSEMITE_STOP_1BIT);
        }
 
        while ((SERIAL_READ(SERIAL_LINE_STATUS) & 0x20) == 0);
diff -rpu linux-mips/arch/mips/pmc-sierra/yosemite/irq.c 
linux-mips-work/arch/mips/pmc-sierra/yosemite/irq.c
--- linux-mips/arch/mips/pmc-sierra/yosemite/irq.c      2004-07-14 
16:21:29.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/irq.c 2004-08-10 
11:33:57.000000000 +0200
@@ -110,7 +110,6 @@ asmlinkage void ll_ht_smp_irq_handler(in
 }
 
 #ifdef CONFIG_KGDB
-extern void init_second_port(void);
 extern void breakpoint(void);
 extern void set_debug_traps(void);
 #endif
@@ -126,18 +125,6 @@ void __init init_IRQ(void)
        init_generic_irq();
        mips_cpu_irq_init(0);
        rm7k_cpu_irq_init(8);
-
-#ifdef CONFIG_KGDB
-       /* At this point, initialize the second serial port */
-       init_second_port();
-       printk("Start kgdb ... \n");
-       set_debug_traps();
-       breakpoint();
-#endif
-
-#ifdef CONFIG_GDB_CONSOLE
-       register_gdb_console();
-#endif
 }
 
 #ifdef CONFIG_KGDB
diff -rpu linux-mips/arch/mips/pmc-sierra/yosemite/setup.c 
linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.c
--- linux-mips/arch/mips/pmc-sierra/yosemite/setup.c    2004-07-20 
11:43:44.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.c       2004-08-11 
11:09:43.493286520 +0200
@@ -22,6 +22,7 @@
  *  with this program; if not, write  to the Free Software Foundation, Inc.,
  *  675 Mass Ave, Cambridge, MA 02139, USA.
  */
+#include <linux/config.h>
 #include <linux/bcd.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
@@ -44,6 +45,7 @@
 #include <asm/reboot.h>
 #include <asm/pci_channel.h>
 #include <asm/serial.h>
+#include <asm/gdb-stub.h>
 #include <linux/termios.h>
 #include <linux/tty.h>
 #include <linux/serial.h>
@@ -58,6 +60,7 @@ unsigned char titan_ge_mac_addr_base[6] 
 
 unsigned long cpu_clock;
 unsigned long yosemite_base;
+volatile unsigned char * serbase;
 
 void __init bus_error_init(void)
 {
@@ -156,11 +159,13 @@ EXPORT_SYMBOL(ocd_base);
 #define TITAN_UART_CLK         3686400
 #define TITAN_SERIAL_BASE_BAUD (TITAN_UART_CLK / 16)
 #define TITAN_SERIAL_IRQ       4
-#define TITAN_SERIAL_BASE      0xfd000008UL
+#define TITAN_SERIAL_BASE      0xfd000000UL
+#define TITAN_SERIAL_REG_SIZE  8
 
 static void __init py_map_ocd(void)
 {
-        struct uart_port up;
+       static const char serr[] = KERN_ERR "Serial port #%u setup failed\n";
+       struct uart_port up;
 
        /*
         * Not specifically interrupt stuff but in case of SMP core_send_ipi
@@ -170,21 +175,45 @@ static void __init py_map_ocd(void)
        if (!ocd_base)
                panic("Mapping OCD failed - game over.  Your score is 0.");
 
+       /* Map uart registers */
+       serbase = (unsigned char *) ioremap(TITAN_SERIAL_BASE, 
TITAN_SERIAL_REG_SIZE * 2);
+       if (!serbase)
+               panic("Failed to map UART registers");
+
+#if defined(CONFIG_SERIAL_8250)
        /*
-        * Register to interrupt zero because we share the interrupt with
-        * the serial driver which we don't properly support yet.
+        * Set up serial port #0. Do not use autodetection; the result is
+        * not what we want.
         */
        memset(&up, 0, sizeof(up));
-       up.membase      = (unsigned char *) ioremap(TITAN_SERIAL_BASE, 8);
+       up.membase      = serbase + TITAN_SERIAL_REG_SIZE;
        up.irq          = TITAN_SERIAL_IRQ;
        up.uartclk      = TITAN_UART_CLK;
        up.regshift     = 0;
        up.iotype       = UPIO_MEM;
-       up.flags        = ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST;
+       up.type         = PORT_16550A;
+       up.flags        = UPF_SHARE_IRQ;
        up.line         = 0;
+       if (early_serial_setup(&up))
+               printk(serr, up.line);
 
+#if CONFIG_SERIAL_8250_NR_UARTS > 1
+       /* And now for port #1. */
+       up.membase      = serbase;
+       up.line         = 1;
        if (early_serial_setup(&up))
-               printk(KERN_ERR "Early serial init of port 0 failed\n");
+               printk(serr, up.line);
+#endif /* CONFIG_SERIAL_8250_NR_UARTS > 1 */
+#endif  /* defined(CONFIG_SERIAL_8250) */
+
+#ifdef CONFIG_KGDB
+       printk(KERN_INFO "Start kgdb ... \n");
+#ifdef CONFIG_GDB_CONSOLE
+       register_gdb_console();
+#endif
+       set_debug_traps();
+       breakpoint();
+#endif
 }
 
 static int __init pmc_yosemite_setup(void)
diff -rpu linux-mips/arch/mips/pmc-sierra/yosemite/setup.h 
linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.h
--- linux-mips/arch/mips/pmc-sierra/yosemite/setup.h    2004-05-24 
12:32:42.000000000 +0200
+++ linux-mips-work/arch/mips/pmc-sierra/yosemite/setup.h       2004-08-10 
11:02:16.000000000 +0200
@@ -28,4 +28,7 @@
 #define        TITAN_ATMEL_24C32_SIZE          32768
 #define        TITAN_ATMEL_24C64_SIZE          65536
 
+/* UART base */
+extern volatile unsigned char * serbase;
+
 #endif /* __SETUP_H__ */
--- linux-mips/arch/mips/configs/yosemite_defconfig     2004-08-11 
10:56:37.292807160 +0200
+++ linux-mips-work/arch/mips/configs/yosemite_defconfig        2004-08-11 
11:22:35.905861960 +0200
@@ -352,8 +352,13 @@ CONFIG_SOUND_GAMEPORT=y
 #
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
-# CONFIG_SERIAL_8250_EXTENDED is not set
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_MULTIPORT is not set
+# CONFIG_SERIAL_8250_RSA is not set
 
 #
 # Non-8250 serial port support

-- 
--------------------------------------------------

Thomas Koeller, Software Development
Basler Vision Technologies

thomas dot koeller at baslerweb dot com
http://www.baslerweb.com

==============================

<Prev in Thread] Current Thread [Next in Thread>