linux-mips-fnet
[Top] [All Lists]

Fw: Trouble in booting my DECstation 5000/260

To: linux-mips@fnet.fr
Subject: Fw: Trouble in booting my DECstation 5000/260
From: "Houten K.H.C. van (Karel)" <K.H.C.vanHouten@research.kpn.com>
Date: Thu, 03 Jun 1999 14:36:35 +0200
Reply-to: K.H.C.vanHouten@research.kpn.com
Hi all,

Hagen has problems with his 260. It seems to panic during bootp.
Has anyone seen this before? Or even has a hint for a solution?

Regards,
Karel.

------- Forwarded Message

Hi,

following your instructions how to boot a DECstation 5000/260 with your
LINUX-Kernel"vmlinux-decR4k.ecoff" i got following error message:

*********************************************************************************
**********************
KN05 V2.1k    (PC: 0x80064684, SP: 0x87ffbcd8)
3/prcache                     3/prcache(14)  * * *
?RST

- -tftp boot(3), bootp .. 193.17.138.81:/tftpboot/vmlinux-decR4k.ecoff
- -tftp load  1239984 +0 +124128
This DECstation is a DS5000/2x0
Loading R4000 MMU routines.
CPU revision is: 00000440
Primary instruction cache 16kb, linesize 16 bytes)
Primary data cache 16kb, linesize 16 bytes)
Secondary cache sized at 1024K linesize 32
Linux version 2.2.1 (root@elrond) (gcc version egcs-2.90.27 980315 (egcs-1.0.2
release)) #2 Sun May 23 11:29:22 MEST 1999
Calibrating delay loop... 59.90 BogoMIPS
Memory: 128160k/131068k available (1080k kernel code, 1540k data)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
TURBOchannel rev. 1 at 25.0 MHz (no parity)
    slot 0: DEC      PMAD-AA  V5.3a
    slot 1: DEC      PMAZ-AA  V5.3d
    slot 2: DEC      PMAZ-AA  V5.3d
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
DECstation Z8530 serial driver version 0.03
tty00 at 0xbf900001 (irq = 4) is a Z85C30 SCC
tty01 at 0xbf900009 (irq = 4) is a Z85C30 SCC
tty02 at 0xbf980001 (irq = 4) is a Z85C30 SCC
tty03 at 0xbf980009 (irq = 4) is a Z85C30 SCC
loop: registered device at major 7
SCSI ID 7  Clock 25 MHz CCF=0 Time-Out 167 NCR53C9x(esp236) detected
ESP: Total of 1 ESP hosts found, 1 actually in use.
scsi0 : ESP236
scsi : 1 host.
  Vendor: DEC       Model: RZ26     (C) DEC  Rev: 392A
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: DEC       Model: RZ26     (C) DEC  Rev: 392A
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
  Vendor: DEC       Model: RRD42   (C) DEC   Rev: 4.5d
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
  Vendor: DEC       Model: TLZ06     (C)DEC  Rev: 0491
  Type:   Sequential-Access                  ANSI SCSI revision: 02
scsi : detected 1 SCSI cdrom 2 SCSI disks total.
sr0: scsi3-mmc drive: 0x/0x caddy
Uniform CDROM driver Revision: 2.52
esp0: target 0 [period 200ns offset 15 5.00MHz synchronous SCSI]
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2050860 [1001 MB] [1.0 GB]
esp0: target 1 [period 200ns offset 15 5.00MHz synchronous SCSI]
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 2050860 [1001 MB] [1.0 GB]
declance.c: v0.008 by Linux Mips DECstation task force
eth0: IOASIC onboard LANCE, addr = 08:00:2b:39:bb:25, irq = 3
eth1: PMAD-AA, addr = 08:00:2b:3c:95:7f, irq = 5
Sending BOOTP requests...<1>Unable to handle kernel paging request at virtual
address 00000000, epc == 8010837c, ra == 801090b8
Oops: 0001
$0 : 00000000 10010c00 0000ffff 00000017
$4 : 00000000 802d4e04 00000196 00000017
$8 : 0000ffff 8012c9e8 00000006 80173ca8
$12: 00000001 00000001 80160000 802d4e02
$16: be000000 802de000 8016d110 802d5040
$20: 00000000 10010c01 be100000 80140000
$24: 00000001 10010c01
$28: 87ffa000 87ffbe28 80140000 801090b8
epc   : 8010837c
Status: 10010c02
Cause : 1000000c
Process swapper (pid: 1, stackpage=87ffa000)
Stack: 10010c01 00000015 80130000 00000f00 802d5040 87fe84a0 8016d110 8016d178
       00000000 00000f00 80160000 800c9bf8 802d5040 00000015 000001b0 80170000
       87fe84a0 802d5040 80180000 800c5154 802d4e10 802d5040 8016d110 8016d178
       802d4e10 802d5040 8016d110 801545e4 00000000 8013b8d9 87ffbd48 00001003
       8016d178 00000188 87fea520 00000000 80160000 00000001 00000e31 80154650
       80140000 ...
Call Trace: [<80130000>] [<800c9bf8>] [<800c5154>] [<8013b8d9>] [<80140000>]
[<801041e8>] [<8013b8bc>] [<8013b8dc>] [<8013b8e4>] [<8013b8e4>] [<80140000>]
[<8004816c>] [<80140000>] [<80049eec>] [<8004816c>] [<8004816c>] [<80048180>]
[<80049efc>] [<80140000>] [<80049eec>]
Code: 24e3ffff  00603821  3063ffff <a4820000> 24840002  94a20000  24a50002
a4820000  24840002
Aiee, killing interrupt handler
*********************************************************************************
**********************

Could you help me ?

Regards

Hagen Schubert




------- End of Forwarded Message


-- 
Karel van Houten

----------------------------------------------------------
The box said "Requires Windows 95 or better."
I can't understand why it won't work on my Linux computer. 
----------------------------------------------------------


<Prev in Thread] Current Thread [Next in Thread>