linux-mips-fnet
[Top] [All Lists]

FYI

To: linux-mips@fnet.fr
Subject: FYI
From: Harald Koerfgen <Harald.Koerfgen@home.ivm.de>
Date: Mon, 15 Feb 1999 14:43:10 +0100 (MET)
Organization: none
Reply-to: "Harald Koerfgen" <Harald.Koerfgen@home.ivm.de>
Sender: harry@franz.no.dom
Hi,

thought you might be interested:


KN05 V2.1k
>>boot 3/tftp/vmlinux.r4k console=ttyS2

[boring stuff snipped]

DECstation Z8530 serial driver version 0.03
tty00 at 0xbf900001 (irq = 4) is a Z85C30 SCC
tty01 at 0xbf900009 (irq = 4) is a Z85C30 SCC
tty02 at 0xbf980001 (irq = 4) is a Z85C30 SCC
tty03 at 0xbf980009 (irq = 4) is a Z85C30 SCC
SCSI ID 7  Clock 25 MHz CCF=0 Time-Out 167 NCR53C9x(esp236) detected
ESP: Total of 1 ESP hosts found, 1 actually in use.
scsi0 : ESP236
scsi : 1 host.
  Vendor: DEC       Model: RZ25     (C) DEC  Rev:
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 2, lun 0
  Vendor: DEC       Model: RZ25     (C) DEC  Rev:
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 3, lun 0
scsi : detected 2 SCSI disks total.
esp0: target 2 [period 200ns offset 15 5.00MHz synchronous SCSI]
sda: Spinning up disk.............ready
SCSI device sda: hdwr sector= 512 bytes. Sectors= 832527 [406 MB] [0.4 GB]
esp0: target 3 [period 200ns offset 15 5.00MHz synchronous SCSI]
sdb: Spinning up disk.............ready
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 832527 [406 MB] [0.4 GB]
declance.c: v0.008 by Linux Mips DECstation task force
eth0: IOASIC onboard LANCE, addr = 08:00:2b:31:a9:ff, irq = 3
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 192.168.0.2, my address is 192.168.0.3
Partition check:
 sda: unknown partition table
 sdb: unknown partition table
Looking up port of RPC 100003/2 on 192.168.0.2
Looking up port of RPC 100005/1 on 192.168.0.2
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 48k freed
INIT: version 2.76 booting
[...]

This is on my DS5k/260 with the onboard NCR 53C94 and rudimentary DMA
support. This is _not_ a fully functional SCSI driver and will _definitely_
_not_ work on other machines. To be honest, I am amazed that the disks are
detected properly and really spin up!

Just wanted to let you know.
---
Regards,
Harald

P.S.: CONFIG_UFS doesn't compile:
fs/filesystems.a(ufs.o): In function `ufs_read_inode':
inode.c(.text+0x81a0): undefined reference to `__fswab64'
inode.c(.text+0x81a0): relocation truncated to fit: R_MIPS_26 __fswab64

Should be easy to fix...

<Prev in Thread] Current Thread [Next in Thread>
  • FYI, Harald Koerfgen <=